Crack Length Influence on Stress Intensity Factors for the Asymmetric Four-point Bending Testing of a Polyurethane Foam

被引：0

作者：

Apostol, Dragos Alexandru ^{[1
]}

Stuparu, Florin ^{[1
]}

Constantinescu, Dan Mihai ^{[1
]}

Marsavina, Liviu ^{[2
]}

Linul, Emanoil ^{[2
]}

机构：

[1] Univ Politehn Bucuresti, Dept Strength Mat, 1-7 Polizu Gh, Bucharest 011061, Romania

[2] Politehn Univ Timisoara, Dept Mech & Strength Mat, Mihai Viteazu Blvd, Timisoara 300222, Romania

来源：

MATERIALE PLASTICE | 2016年 / 53卷 / 02期

关键词：

mixed-mode; polyurethane foams; asymmetric four-point bending; crack length; FRACTURE-TOUGHNESS;

D O I：

暂无

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Mixed mode four-point testing is performed on polyurethane foams. This paper presents only the results on the stress intensity factors (SIFs) obtained experimentally for a density of 325 kg/m(3), although tests were done for three foam densities. An asymmetric four-point bending setup was used for determining the critical SIFs in Mode I and Mode II, and discussions on the influence of the initial crack length on the SIF values are done. As initial crack length is increased the theoretical predictions give a better comparison to experimentally obtained results.

引用

页码：280 / 282

页数：3

共 50 条

[31] Shear properties of wood measured by the asymmetric four-point bending test of notched specimen
Yoshihara, Hiroshi
HOLZFORSCHUNG, 2009, 63 (02) : 211 - 216
[32] Measurement of stress factors and residual stress of a film by in situ X-ray diffraction during four-point bending
Ortolani, Matteo
Ricardo, Cristy Leonor Azanza
Scardi, Paolo
JOURNAL OF APPLIED CRYSTALLOGRAPHY, 2009, 42 : 1102 - 1109
[33] In-plane shear strength of paper measured by asymmetric four-point bending test
Yoshihara, Hiroshi
Yoshinobu, Masahiro
HOLZFORSCHUNG, 2015, 69 (01) : 41 - 46
[34] THE INFLUENCE OF APPLIED STRESS, CRACK LENGTH, AND STRESS INTENSITY FACTOR ON CRACK CLOSURE
MCCLUNG, RC
METALLURGICAL TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1991, 22 (07): : 1559 - 1571
[35] Fatigue crack extension in four-point bending test for steels imitated heat affected zone
Dept. of Mech. Sci. Bioeng., G. School of Eng. Sci., Osaka Univ., Machikaneyamacho, Toyonaka
560-8531, Japan
不详
660-0891, Japan
不详
739-8527, Japan
不详
950-2181, Japan
Zairyo, 4 (323-329):
[36] Crack propagation characterisation of bituminous mixtures using a four-point bending notched specimen test
Mai Lan Nguyen
Di Benedetto, Herve
Sauzeat, Cedric
ROAD MATERIALS AND PAVEMENT DESIGN, 2016, 17 (01) : 70 - 86
[37] Shear stress shear strain relation of wood obtained by asymmetric four-point bending test of side-tapered specimen
Yoshihara, H
Suzuki, A
JOURNAL OF TESTING AND EVALUATION, 2005, 33 (01) : 55 - 60
[38] Study of asymmetric glass reinforced plastic beams in off-axis four-point bending
Theotokoglou, Efstathios E.
Sideridis, Emilio P.
JOURNAL OF COMPOSITE MATERIALS, 2015, 49 (05) : 587 - 599
[39] STRESS INTENSITY FACTORS FOR EDGE CRACK SUBJECTED TO MIXED-MODE 4-POINT BENDING
FETT, T
THEORETICAL AND APPLIED FRACTURE MECHANICS, 1991, 15 (01) : 99 - 104
[40] Determination of the Dynamic Stress Intensity Factor for the Four-Point Bend Impact Test
Rokach, Ihor V.
Labedzki, Pawel
INTERNATIONAL JOURNAL OF FRACTURE, 2009, 160 (01) : 93 - 100

← 1 2 3 4 5 →