Crack Length Influence on Stress Intensity Factors for the Asymmetric Four-point Bending Testing of a Polyurethane Foam

被引：0

作者：

Apostol, Dragos Alexandru ^{[1
]}

Stuparu, Florin ^{[1
]}

Constantinescu, Dan Mihai ^{[1
]}

Marsavina, Liviu ^{[2
]}

Linul, Emanoil ^{[2
]}

机构：

[1] Univ Politehn Bucuresti, Dept Strength Mat, 1-7 Polizu Gh, Bucharest 011061, Romania

[2] Politehn Univ Timisoara, Dept Mech & Strength Mat, Mihai Viteazu Blvd, Timisoara 300222, Romania

来源：

MATERIALE PLASTICE | 2016年 / 53卷 / 02期

关键词：

mixed-mode; polyurethane foams; asymmetric four-point bending; crack length; FRACTURE-TOUGHNESS;

D O I：

暂无

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Mixed mode four-point testing is performed on polyurethane foams. This paper presents only the results on the stress intensity factors (SIFs) obtained experimentally for a density of 325 kg/m(3), although tests were done for three foam densities. An asymmetric four-point bending setup was used for determining the critical SIFs in Mode I and Mode II, and discussions on the influence of the initial crack length on the SIF values are done. As initial crack length is increased the theoretical predictions give a better comparison to experimentally obtained results.

引用

页码：280 / 282

页数：3

共 50 条

[21] Fatigue Crack Propagation in 5754 Aluminum Alloy under Four-Point Bending
Makhatha M.E.
Kumar P.
Baruwa D.A.
Defect and Diffusion Forum, 2024, 430 : 55 - 62
[22] DYNAMIC RESPONSE OF A BEAM WITH A CRACK SUBJECTED TO FOUR-POINT IMPACT BENDING.
Shibahara, Masao
Matsui, Yoshio
Bulletin of the JSME, 1986, 29 (248): : 370 - 376
[23] Crack path investigation using the generalized maximum tangential stress criterion: antisymmetrical four-point bending specimen
Malikova, Lucie
ENGINEERING DECISIONS AND SCIENTIFIC RESEARCH IN AEROSPACE, ROBOTICS, BIOMECHANICS, MECHANICAL ENGINEERING AND MANUFACTURING, 2013, 436 : 108 - 113
[24] STRESS INTENSITY FACTORS FOR THE BENDING OF A CIRCULAR PLATE WITH A CRACK
BEREZHNITSKII, LT
MAZURAK, LP
SOVIET APPLIED MECHANICS, 1982, 18 (03): : 252 - 256
[25] A four-point bending technique for studying subcritical crack growth in thin films and at interfaces
Qing Ma
Journal of Materials Research, 1997, 12 : 840 - 845
[26] Studies on subcritical crack growth in facade rock panel using four-point bending
Kwok, K. W.
Wong, R. H. C.
Chau, K. T.
Wong, T. -f.
FRACTURE AND FAILURE OF NATURAL BUILDING STONES: APPLICATION IN THE RESTORATION OF ANCIENT MONUMENTS, 2006, : 19 - +
[27] Mixed-mode fracture of ceramics in asymmetric four-point bending: Effect of crack-face grain interlocking/bridging
Li, M
Sakai, M
JOURNAL OF THE AMERICAN CERAMIC SOCIETY, 1996, 79 (10) : 2718 - 2726
[28] Interfacial fracture testing of deposited metal layers under four-point bending
Klingbeil, NW
Beuth, JL
ENGINEERING FRACTURE MECHANICS, 1997, 56 (01) : 113 - 126
[29] A four-point bending technique for studying subcritical crack growth in thin films and at interfaces
Ma, Q
JOURNAL OF MATERIALS RESEARCH, 1997, 12 (03) : 840 - 845
[30] Four-point bending cycling as alternative for Thermal cycling solder fatigue testing
Vandevelde, Bart
Vanhee, Filip
Pissoort, Davy
Degrendele, Lieven
De Baets, Johan
Allaert, Bart
Lauwaert, Ralph
Labie, Riet
Willems, Geert
2016 17TH INTERNATIONAL CONFERENCE ON THERMAL, MECHANICAL AND MULTI-PHYSICS SIMULATION AND EXPERIMENTS IN MICROELECTRONICS AND MICROSYSTEMS (EUROSIME), 2016,

← 1 2 3 4 5 →