Experimental Investigations on the Effect of Vegetable Based Cutting Fluid in Turning AISI 1040 Steel

被引：1

作者：

Jhodkar, Durwesh ^{[1
]}

Amaranth, M. ^{[1
]}

Chelladurai, H. ^{[1
]}

Ramkumar, J. ^{[2
]}

机构：

[1] Indian Inst Informat & Technol Design & Mfg, Dept Mech Engn, Jabalpur 482005, India

[2] Indian Inst Technol, Dept Mech Engn, Kanpur 208016, Uttar Pradesh, India

来源：

ENGINEERING AND MANUFACTURING TECHNOLOGIES | 2014年 / 541-542卷

关键词：

Tool wear; flank; crater; coconut oil; TOOL WEAR; COCONUT OIL; LUBRICANTS;

D O I：

10.4028/www.scientific.net/AMM.541-542.368

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

Application of petroleum based cutting fluids in machining operation may cause many problems such as eye burn and skin inflation etc. Vegetables oils are good alternative to overcome such issues. In this work, experiments were carried out to study the influence of coconut oil on the performance of single point cutting tool insert in turning operation. Three cutting conditions viz. dry, wet and coconut oil were considered to evaluate the tool wear. Results obtained from the experiments highlighted the advantages of coconut oil, a considerable reduction in flank wear, crater wear and auxiliary wear was observed in the turning operation.

引用

页码：368 / +

页数：2

共 50 条

[41] Effect of cutting parameters in the surface residual stresses generated by turning in AISI 4340 steel
Garcia Navas, Virginia
Gonzalo, Oscar
Bengoetxea, Ion
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2012, 61 : 48 - 57
[42] Performance assessment of microwave treated WC insert while turning AISI 1040 steel
Jhodkar, Durwesh
Amarnath, M.
Chelladurai, H.
Ramkumar, J.
JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY, 2018, 32 (06) : 2551 - 2558
[43] Performance assessment of microwave treated WC insert while turning AISI 1040 steel
Durwesh Jhodkar
M. Amarnath
H. Chelladurai
J. Ramkumar
Journal of Mechanical Science and Technology, 2018, 32 : 2551 - 2558
[44] Experimental and numerical investigation of cutting forces during turning of cylindrical AISI 4340 steel specimens
Iynen, Ogur
Eksi, Abdul Kadir
Ozdemir, Mustafa
Akyildiz, Hamza Kemal
MATERIALS TESTING, 2021, 63 (05) : 402 - 410
[45] Optimization of machining parameters in turning of AISI 1040 steel using hybrid MCDM technique
Vats, Prameet
Singh, Tushar
Dubey, Vineet
Sharma, Anuj Kumar
MATERIALS TODAY-PROCEEDINGS, 2022, 50 : 1758 - 1765
[46] Experimental Study on Joining of AA6063 and AISI 1040 steel
Hynes, N. Rajesh Jesudoss
Raja, S.
2ND INTERNATIONAL CONFERENCE ON CONDENSED MATTER AND APPLIED PHYSICS (ICC-2017), 2018, 1953
[47] Specimen geometry effect on the mechanical properties of AISI 1040 steel
Calik, Adrian
Sahin, Osman
Ucar, Nazim
ZEITSCHRIFT FUR NATURFORSCHUNG SECTION A-A JOURNAL OF PHYSICAL SCIENCES, 2008, 63 (7-8): : 448 - 452
[48] Analysis and optimisation of the cutting parameters based on machinability factors in turning AISI 4140 steel
Ozdemir, Mustafa
Sahinoglu, Abidin
Rafighi, Mohammad
Yilmaz, Volkan
CANADIAN METALLURGICAL QUARTERLY, 2022, 61 (04) : 407 - 417
[49] Influence of the direction and flow rate of the cutting fluid on tool life in turning process of AISI 1045 steel
Diniz, Anselmo Eduardo
Micaroni, Ricardo
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2007, 47 (02): : 247 - 254
[50] Experimental investigation on the performance of MQL drilling of AISI 321 stainless steel using nano-graphene enhanced vegetable-oil-based cutting fluid
Pal, Amrit
Chatha, Sukhpal Singh
Sidhu, Hazoor Singh
TRIBOLOGY INTERNATIONAL, 2020, 151 (151)

← 1 2 3 4 5 →