Turning of Aluminum Alloy Al-6063 under Dry and Wet Condition using CVD Coated Tool

被引：2

作者：

Zakaria, M. S. ^{[1
]}

Afiq, Adam ^{[1
]}

Hafiz, Muhammad ^{[1
]}

Jamalludin, Mohd Riduan ^{[1
]}

Rosli, M. U. ^{[1
]}

Rahim, Wan M. Faizal Wan A. ^{[1
]}

Ishak, Muhammad Ikman ^{[1
]}

Khor, C. Y. ^{[1
]}

Nawi, M. A. M. ^{[1
]}

Shahrin, Suhaimi ^{[1
]}

机构：

[1] Univ Malaysia Perlis, Fac Engn Technol, KampusUniCITI Alam, Padang Besar 02100, Perlis, Malaysia

来源：

GREEN DESIGN AND MANUFACTURE: ADVANCED AND EMERGING APPLICATIONS | 2018年 / 2030卷

关键词：

PERFORMANCE; SPEED;

D O I：

10.1063/1.5066670

中图分类号：

X [环境科学、安全科学];

学科分类号：

08 ; 0830 ;

摘要：

In present paper, cutting parameters are investigated in turning of Al-6063 using carbide inserts based on two level factorial design. The cutting insert with CVD coated TiC + Al2O3 + TiN. Experiments is conducted in dry and wet condition. The selected cutting parameters for turning process are cutting speed, feed rate and depth of cut with each two levels, maintaining nose radius and rake angle. It is found feed rate is the most significant factor affecting surface roughness and followed by cutting speed and depth of cut. The minimum surface roughness is obtained when low feed rate and low cutting speed are employed in wet condition.

引用

页数：5

共 50 条

[31] A Comparison of Machinability in Hard Turning of EN-24 Alloy Steel Under Mist Cooled and Dry Cutting Environments with a Coated Cermet Tool
Anshuman Das
Nirmal Tirkey
Saroj Kumar Patel
Sudhansu Ranjan Das
Bibhuti Bhusan Biswal
Journal of Failure Analysis and Prevention, 2019, 19 : 115 - 130
[32] Experimental investigation on cutting tool performance during turning AA 6063 using uncoated and multilayer coated carbide inserts
Das, Dipti Kanta
Mishra, Purna Chandra
Sahoo, Ashok Kumar
Ghosh, Dipankar
International Journal of Machining and Machinability of Materials, 2015, 17 (3-4) : 277 - 294
[33] Experimental investigation on cutting tool performance during turning AA 6063 using uncoated and multilayer coated carbide inserts
School of Mechanical Engineering, KIIT University, Bhubaneswar, Odisha
751024, India
Int. J. Mach. Mach. Mater., 3-4 (277-294):
[34] Comparative study of tool wear in milling titanium alloy (Ti-6Al-4V) using PVD and CVD coated cutting tool
Abdullah, Raja Izamshah Raja
Redzuwan, Bahrin Ikram
Aziz, Mohd Sanusi Abdul
Kasim, Mohd Shahir
INDUSTRIAL LUBRICATION AND TRIBOLOGY, 2017, 69 (03) : 363 - 370
[35] Research on Machinability of Dry Cutting 7075 Aluminum Alloy with TiN Coating Micro-Texture Turning Tool
Xu, Tiantian
Shi, Hu
Wang, Baizhong
Liu, Jinpeng
JOURNAL OF NANOELECTRONICS AND OPTOELECTRONICS, 2024, 19 (03) : 284 - 292
[36] Contact fatigue behavior of α-Al2O3-Ti(C,N) CVD coated WC-Co under dry and wet conditions
Sosa, A. D.
Cipres, V. Collado
Garcia, J. L.
Dalibon, E. L.
Escalada, L.
Roa, J. J.
Soldera, F.
Bruehl, S. P.
Llanes, L.
Simison, S.
MATERIALS LETTERS, 2021, 284
[37] Tool Wear Analysis during Ultrasonic Assisted Turning of Nimonic-90 under Dry and Wet Conditions
Airao, Jay
Nirala, Chandrakant K.
Lopez de Lacalle, Luis Noberto
Khanna, Navneet
METALS, 2021, 11 (08)
[38] Wear Resistance of Coated SAE 305 Aluminum Alloy Under Dry Friction Reciprocate Sliding
Pires, M. S. T.
Doca, T.
Steier, V. F.
da Silva, W. M.
Oliveira Junior, M. M.
TRIBOLOGY LETTERS, 2018, 66 (02)
[39] Wear Resistance of Coated SAE 305 Aluminum Alloy Under Dry Friction Reciprocate Sliding
M. S. T. Pires
T. Doca
V. F. Steier
W. M. da Silva
M. M. Oliveira Júnior
Tribology Letters, 2018, 66
[40] Development of DLC Coated Tool for Cutting of Aluminum Alloy -Influence of deposition condition on cutting characteristic-
Minaki, Kazushi
Kitajima, Koichi
Nakahira, Yu
Ohnishi, Masami
Sugimoto, Takashi
Kaminomura, Shun
ADVANCES IN ABRASIVE TECHNOLOGY XI, 2009, 389-390 : 163 - +

← 1 2 3 4 5 →