Turning of Aluminum Alloy Al-6063 under Dry and Wet Condition using CVD Coated Tool

被引：2

作者：

Zakaria, M. S. ^{[1
]}

Afiq, Adam ^{[1
]}

Hafiz, Muhammad ^{[1
]}

Jamalludin, Mohd Riduan ^{[1
]}

Rosli, M. U. ^{[1
]}

Rahim, Wan M. Faizal Wan A. ^{[1
]}

Ishak, Muhammad Ikman ^{[1
]}

Khor, C. Y. ^{[1
]}

Nawi, M. A. M. ^{[1
]}

Shahrin, Suhaimi ^{[1
]}

机构：

[1] Univ Malaysia Perlis, Fac Engn Technol, KampusUniCITI Alam, Padang Besar 02100, Perlis, Malaysia

来源：

GREEN DESIGN AND MANUFACTURE: ADVANCED AND EMERGING APPLICATIONS | 2018年 / 2030卷

关键词：

PERFORMANCE; SPEED;

D O I：

10.1063/1.5066670

中图分类号：

X [环境科学、安全科学];

学科分类号：

08 ; 0830 ;

摘要：

In present paper, cutting parameters are investigated in turning of Al-6063 using carbide inserts based on two level factorial design. The cutting insert with CVD coated TiC + Al2O3 + TiN. Experiments is conducted in dry and wet condition. The selected cutting parameters for turning process are cutting speed, feed rate and depth of cut with each two levels, maintaining nose radius and rake angle. It is found feed rate is the most significant factor affecting surface roughness and followed by cutting speed and depth of cut. The minimum surface roughness is obtained when low feed rate and low cutting speed are employed in wet condition.

引用

页数：5

共 50 条

[21] Dry turning of tempered martensitic stainless tool steel using coated cermet and coated carbide tools
Noordin, M. Y.
Venkatesh, V. C.
Sharif, S.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2007, 185 (1-3) : 83 - 90
[22] Comparative assessment of machining efficiency in turning of Ti-6Al-4V alloy under dry, wet, and MQL conditions
Sharma, Saurabh
Das, Partha Protim
Ladakhi, T. Y.
Pradhan, B. B.
Phipon, Ruben
INTERNATIONAL JOURNAL OF INTERACTIVE DESIGN AND MANUFACTURING - IJIDEM, 2024,
[23] Optimization of Cutting Parameters in Dry Turning of AISI 4140 Hardened Alloy Steel with Coated Carbide Tool
Mane, Sandip
Kumar, Sanjay
PROCEEDINGS OF INTERNATIONAL CONFERENCE ON INTELLIGENT MANUFACTURING AND AUTOMATION (ICIMA 2018), 2019, : 455 - 462
[24] Technological and sustainability implications of dry, near-dry, and wet turning of Ti-6Al-4V alloy
Maria Giulia Faga
Paolo C. Priarone
Matteo Robiglio
Luca Settineri
Vincenzo Tebaldo
International Journal of Precision Engineering and Manufacturing-Green Technology, 2017, 4 : 129 - 139
[25] Technological and Sustainability Implications of Dry, Near-Dry, and Wet Turning of Ti-6Al-4V Alloy
Faga, Maria Giulia
Priarone, Paolo C.
Robiglio, Matteo
Settineri, Luca
Tebaldo, Vincenzo
INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING-GREEN TECHNOLOGY, 2017, 4 (02) : 129 - 139
[26] Investigation on machinability characteristics during turning Al6063 alloy using uncoated carbide insert
Sahoo, Ashok Kumar
Panda, Amlana
Kumar, Ramanuj
Das, Rabin Kumar
Das, Diptikanta
MATERIALS TODAY-PROCEEDINGS, 2018, 5 (09) : 18120 - 18128
[27] Simulation and Experimental Studies on Sliding Wear of Aluminum Alloy under Dry Condition using Asymmetric Contact Models
Salunkhe, V. G.
Gajakosh, Amith Kumar
Jacob
Thimmaiah, Jagadeesha
EMERGING TRENDS IN MECHANICAL ENGINEERING 2018, 2019, 2080
[28] Development of DLC coated tool for cutting of aluminum alloy - Influence of deposition condition on cutting characteristic
Minaki, Kazushi
Kitajima, Koichi
Nakahira, Yu
Ohnishi, Masami
Sugimoto, Takashi
Kaminomura, Shun
Key Engineering Materials, 2009, 389-390 : 163 - 168
[29] Study on the Cutting Performance of HFCVD Diamond coated Silicon Nitride Inserts in Dry Turning Aluminum Silicon Alloy
Sun, Fanghong
Shen, Bin
Yang, Guodong
ADVANCES IN ABRASIVE TECHNOLOGY XIII, 2010, 126-128 : 226 - 231
[30] A Comparison of Machinability in Hard Turning of EN-24 Alloy Steel Under Mist Cooled and Dry Cutting Environments with a Coated Cermet Tool
Das, Anshuman
Tirkey, Nirmal
Patel, Saroj Kumar
Das, Sudhansu Ranjan
Biswal, Bibhuti Bhusan
JOURNAL OF FAILURE ANALYSIS AND PREVENTION, 2019, 19 (01) : 115 - 130

← 1 2 3 4 5 →