INVESTIGATION OF THE USABILITY OF CUBIC BORON NITRIDE CUTTING TOOLS AS AN ALTERNATIVE TO DIAMOND CUTTING TOOLS

被引：6

作者：

Islak, S. ^{[1
]}

Kir, D. ^{[2
]}

Celik, H. ^{[3
]}

机构：

[1] Kastamonu Univ, Fac Engn & Architecture, Dept Mat Sci & Nanotechnol Engn, TR-37000 Kastamonu, Turkey

[2] Kocaeli Univ, Hereke Vocat High Sch, TR-41400 Kocaeli, Turkey

[3] Firat Univ, Fac Technol, Dept Met & Mat Engn, TR-23100 Elazig, Turkey

来源：

ARCHIVES OF METALLURGY AND MATERIALS | 2013年 / 58卷 / 04期

关键词：

cBN cutting tools; hot-pressing technique; wear; CBN; WEAR;

D O I：

10.2478/amm-2013-0135

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

Diamond and cubic boron nitride (cBN) cutting segments were produced using hot pressing technique for this study to be used in cutting natural stone. cBN grains were added to bronze powder, the chosen matrix, at a rate of 0%, 20%, 40%, 60%, 80%, and 100% (according to percentage by weight). Segments were produced under a pressure of 35 MPa, at a sintering temperature of 600 degrees C, over a sintering time of 3 minutes. The cutting properties of the produced segments were determined by cutting Ankara andesite. A Scanning Electron Microscope (SEM) and an X-Ray Diffractometer (XRD) were used to analyse the microstructure, phase compound, and wear surfaces of each segment type.

引用

页码：1119 / 1123

页数：5

共 50 条

[41] Production of diamond impregnated cutting tools
Dwan, JD
POWDER METALLURGY, 1998, 41 (02) : 84 - 86
[42] Diamond Coated Surgical Cutting Tools
Jackson, M. J.
Robinson, G. M.
Whitfield, M. D.
Handy, R.
Ahmed, W.
Sein, H.
Taylor, H.
SURFACE ENGINEERING, PROCEEDINGS, 2006, : 196 - +
[43] Diamond composite rock cutting tools
Boland, JN
Clark, P
Harbers, C
Li, X
Alehossein, H
EURO PM 2002: DIAMOND TOOLING PROCEEDINGS, 2002, : 103 - 108
[44] FRACTURE AND WEAR OF DIAMOND CUTTING TOOLS
WONG, CJ
JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY-TRANSACTIONS OF THE ASME, 1981, 103 (04): : 341 - 345
[45] DIAMOND HARD COATS FOR CUTTING TOOLS
不详
MANUFACTURING ENGINEERING, 1991, 106 (06): : 24 - &
[46] Behaviour of diamond coatings on cutting tools
Rousseau, J
Paulmier, D
Mathia, T
Le Huu, T
Zaidi, H
Govin, F
Larose, JF
TRIBOLOGY FOR ENERGY CONSERVATION, 1998, 34 : 357 - 363
[47] Diamond planing of coated cutting tools
Barats, Ya.I.
Tikhonov, D.A.
Russian Engineering Research, 2008, 28 (03) : 275 - 276
[48] DIAMOND CUTTING TOOLS - EMERGING TECHNOLOGY
DEUTSCHLER, KA
THEOPHILE, G
WOOD & WOOD PRODUCTS, 1984, 89 (09): : 206 - 210
[49] BORE FINISHING WITH DIAMOND CUTTING TOOLS
HUNZIKER, HR
INDUSTRIAL DIAMOND REVIEW, 1982, 42 (03): : 142 - 144
[50] Polishing of diamond composite cutting tools
Chen, Y.
Zhang, L. C.
Arsecularatne, J. A.
INTERNATIONAL JOURNAL OF SURFACE SCIENCE AND ENGINEERING, 2007, 1 (04) : 360 - 373

← 1 2 3 4 5 →