Cryogenic machining of hard-to-cut materials

被引：251

作者：

Wang, ZY ^{[1
]}

Rajurkar, KP

机构：

[1] Univ Nevada, Dept Mech Engn, Las Vegas, NV 89154 USA

[2] Univ Nebraska, Dept Ind & Management Syst Engn, Lincoln, NE 68588 USA

来源：

WEAR | 2000年 / 239卷 / 02期

关键词：

cryogenic turning; ceramics; titanium; inconel; tantalum;

D O I：

10.1016/S0043-1648(99)00361-0

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

This paper presents a technique for machining of advanced ceramics with liquid nitrogen (LN2) cooled polycrystalline cubic boron nitride (PCBN) tool, titanium alloys, Inconel alloys, and tantalum with cemented carbide tools. With LN2 cooling, the temperature in the cutting zone is reduced to a lower range, therefore, the hot-strength and hot-hardness of the tool remain high, and the temperature-dependent tool wear reduces significantly under all machining conditions. The surface roughness of all materials machined with LN2 cooling were found to be much better than the surface roughness of materials machined without LN2 cooling after the same length of cutting. (C) 2000 Elsevier Science S.A. All rights reserved.

引用

页码：168 / 175

页数：8

共 50 条

[41] HYBRID MACHINING OF HARD AND BRITTLE MATERIALS
KOSHIMIZU, S
IANSAKI, I
JOURNAL OF MECHANICAL WORKING TECHNOLOGY, 1988, 17 : 333 - 341
[42] MACHINING OF HARD FERROUS MATERIALS WITH AMBORITE
NOTTER, AT
HEATH, PJ
INDUSTRIAL DIAMOND REVIEW, 1980, (JUL): : 244 - 251
[43] The Diagnostics of Abrasive Tools After Internal Cylindrical Grinding of Hard-to-Cut Materials by Means of a Laser Technique Using Imaging and Analysis of Scattered Light
Kaplonek, W.
Nadolny, K.
ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING, 2013, 38 (04) : 953 - 970
[44] THE EFFECT OF CRYOGENIC COOLING ON WHITE LAYER FORMATION IN HARD MACHINING
Umbrello, D.
Caruso, S.
Yang, S.
Crea, F.
Dillon, O. W., Jr.
Jawahir, I. S.
PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION 2011, VOL 3, 2012, : 341 - 348
[45] ELECTRICAL DISCHARGE MACHINING OF DIFFICULT TO CUT MATERIALS
Swiercz, Rafal
Oniszczuk-Swiercz, Dorota
Dabrowski, Lucjan
ARCHIVE OF MECHANICAL ENGINEERING, 2018, 65 (04) : 461 - 476
[46] Influence of the depth of cut on the AM nitinol properties in flood and cryogenic machining
Guarise, Alessandra
Bertolini, Rachele
Ghiotti, Andrea
Bruschi, Stefania
MATERIAL FORMING, ESAFORM 2024, 2024, 41 : 1925 - 1934
[47] Laser assisted jet electrochemical machining of hard to cut alloys
Pajak, PT
De Silva, AKM
Harrison, DK
McGeough, JA
PROCEEDINGS OF THE 34TH INTERNATIONAL MATADOR CONFERENCE: FORMERLY THE INTERNATIONAL MACHINE TOOL DESIGN AND RESEARCH CONFERENCES, 2004, : 265 - 271
[48] COOLING STRATEGIES FOR CRYOGENIC MACHINING FROM A MATERIALS VIEWPOINT
ZHAO, Z
HONG, SY
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 1992, 1 (05) : 669 - 678
[49] A study on chip breakage in mini-pore vibration drilling for hard-to-cut material of austenitic stainless steel
Zhou, J. S.
Ye, B. Y.
Lai, X. Y.
MANUFACTURING AUTOMATION TECHNOLOGY DEVELOPMENT, 2011, 455 : 548 - 552
[50] Modelling and Analysis of Surface Evolution on Turning of Hard-to-Cut CLARM 30NiCrMoV14 Steel Alloy
Raza, Syed Muhammad
Khan, Aqib Mashood
Farooq, Muhammad Umar
Iqbal, Asif
Pimenov, Danil Yurievich
Giasin, Khaled
Leksycki, Kamil
METALS, 2021, 11 (11)

← 1 2 3 4 5 →