Cryogenic machining of hard-to-cut materials

被引：251

作者：

Wang, ZY ^{[1
]}

Rajurkar, KP

机构：

[1] Univ Nevada, Dept Mech Engn, Las Vegas, NV 89154 USA

[2] Univ Nebraska, Dept Ind & Management Syst Engn, Lincoln, NE 68588 USA

来源：

WEAR | 2000年 / 239卷 / 02期

关键词：

cryogenic turning; ceramics; titanium; inconel; tantalum;

D O I：

10.1016/S0043-1648(99)00361-0

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

This paper presents a technique for machining of advanced ceramics with liquid nitrogen (LN2) cooled polycrystalline cubic boron nitride (PCBN) tool, titanium alloys, Inconel alloys, and tantalum with cemented carbide tools. With LN2 cooling, the temperature in the cutting zone is reduced to a lower range, therefore, the hot-strength and hot-hardness of the tool remain high, and the temperature-dependent tool wear reduces significantly under all machining conditions. The surface roughness of all materials machined with LN2 cooling were found to be much better than the surface roughness of materials machined without LN2 cooling after the same length of cutting. (C) 2000 Elsevier Science S.A. All rights reserved.

引用

页码：168 / 175

页数：8

共 50 条

[31] Design and performance of AlTiN and TiAlCrN PVD coatings for machining of hard to cut materials
Fox-Rabinovich, G. S.
Kovalev, A. I.
Aguirre, M. H.
Beake, B. D.
Yamamoto, K.
Veldhuis, S. C.
Endrino, J. L.
Wainstein, D. L.
Rashkovskiy, A. Y.
SURFACE & COATINGS TECHNOLOGY, 2009, 204 (04): : 489 - 496
[32] Heating Current Control in Electric Hot Minipore drilling hard-to-cut material
Xu, L. Y.
Wu, Q.
Ye, B. Y.
Hu, X. F.
Li, Y. Z. H.
Qu, X. I.
MECHANICAL ENGINEERING AND GREEN MANUFACTURING, PTS 1 AND 2, 2010, : 1605 - +
[33] INVESTIGATING TURNING OF HARD-TO-CUT MATERIAL USING SELF-PROPELLED ROTARY TOOL
El-Mounayri, H.
Razak, A. Latif
Kessler, M.
PROCEEDINGS OF THE ASME INTERNATIONAL MANUFACTURING SCIENCE AND ENGINEERING CONFERENCE 2011, VOL 2, 2011, : 331 - 338
[34] CONSERVE DIAMOND BORT AND CUT HARD-TO-MACHINE MATERIALS WITH NEW MACHINING PROCESSES
不详
JOURNAL OF METALS, 1952, 4 (04): : 378 - 380
[35] Investigation of a green nanofluid added with graphene and Al 2 O 3 nano-additives for grinding hard-to-cut materials
Li, Wei
Zeng, Zhixiong
Le, Shajiu
Zhu, Keyi
Huang, Xiangming
Hegab, Hussien
Ibrahim, Ahmed Mohamed Mahmoud
TRIBOLOGY INTERNATIONAL, 2024, 195
[36] The effects of Cryogenic Cooling on Surface Integrity in Hard Machining
Umbrello, D.
Pu, Z.
Caruso, S.
Outeiro, J. C.
Jayal, A. D.
Dillon, O. W., Jr.
Jawahir, I. S.
1ST CIRP CONFERENCE ON SURFACE INTEGRITY (CSI), 2011, 19
[37] Modelling the dynamic behaviour of hard-to-cut alloys under conditions of vibro-impact cutting
Muhammad, R.
Demiral, M.
Roy, A.
Silberschmidt, V. V.
INTERNATIONAL SYMPOSIUM ON DYNAMIC DEFORMATION AND FRACTURE OF ADVANCED MATERIALS (D2FAM 2013), 2013, 451
[38] The effects of cryogenic cooling on surface integrity in hard machining: A comparison with dry machining
Umbrello, Domenico
Micari, Fabrizio
Jawahir, I. S.
CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2012, 61 (01) : 103 - 106
[39] The influence of depth of cut on cryogenic machining performance of hardened steel
Gharibi, Armin
Kaynak, Yusuf
JOURNAL OF THE FACULTY OF ENGINEERING AND ARCHITECTURE OF GAZI UNIVERSITY, 2019, 34 (02): : 582 - 596
[40] The Diagnostics of Abrasive Tools After Internal Cylindrical Grinding of Hard-to-Cut Materials by Means of a Laser Technique Using Imaging and Analysis of Scattered Light
W. Kapłonek
K. Nadolny
Arabian Journal for Science and Engineering, 2013, 38 : 953 - 970

← 1 2 3 4 5 →