Cryogenic machining of hard-to-cut materials

被引：251

作者：

Wang, ZY ^{[1
]}

Rajurkar, KP

机构：

[1] Univ Nevada, Dept Mech Engn, Las Vegas, NV 89154 USA

[2] Univ Nebraska, Dept Ind & Management Syst Engn, Lincoln, NE 68588 USA

来源：

WEAR | 2000年 / 239卷 / 02期

关键词：

cryogenic turning; ceramics; titanium; inconel; tantalum;

D O I：

10.1016/S0043-1648(99)00361-0

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

This paper presents a technique for machining of advanced ceramics with liquid nitrogen (LN2) cooled polycrystalline cubic boron nitride (PCBN) tool, titanium alloys, Inconel alloys, and tantalum with cemented carbide tools. With LN2 cooling, the temperature in the cutting zone is reduced to a lower range, therefore, the hot-strength and hot-hardness of the tool remain high, and the temperature-dependent tool wear reduces significantly under all machining conditions. The surface roughness of all materials machined with LN2 cooling were found to be much better than the surface roughness of materials machined without LN2 cooling after the same length of cutting. (C) 2000 Elsevier Science S.A. All rights reserved.

引用

页码：168 / 175

页数：8

共 50 条

[21] Preparation and evaluation of a stable CNT-water based nano cutting fluid for machining hard-to-cut material
Sharmin, Israt
Gafur, Md Abdul
Dhar, Nikhil Ranjan
SN APPLIED SCIENCES, 2020, 2 (04):
[22] Preparation and evaluation of a stable CNT-water based nano cutting fluid for machining hard-to-cut material
Israt Sharmin
Md. Abdul Gafur
Nikhil Ranjan Dhar
SN Applied Sciences, 2020, 2
[23] Performance analysis of uncoated tools for machining of hard to cut materials
Lokireddi, V. V. Gopala Rao
Vajrapu, S. V. Satyanarayana
Sai, P. Sarat Chandra
Vijay, S.
MATERIALS TODAY-PROCEEDINGS, 2022, 60 : 902 - 906
[24] Machining of Hard-to-Cut Materials: Impact of Varying Weight Proportion of Boron Carbide Particle Addition on Cutting Force and Surface Roughness of Al6061
Hiremath, Vijaykumar
Bharath, V
Auradi, V
Dundur, S. T.
Nagaral, Madeva
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2022, 31 (05) : 3784 - 3791
[25] Flank wear of twist drills and surface quality of holes in hard-to-cut materials by electric hot drilling
Lanying Xu
Qiang Wu
Mengyang Qin
Yong Tang
The International Journal of Advanced Manufacturing Technology, 2016, 84 : 513 - 522
[26] Flank wear of twist drills and surface quality of holes in hard-to-cut materials by electric hot drilling
Xu, Lanying
Wu, Qiang
Qin, Mengyang
Tang, Yong
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2016, 84 (1-4): : 513 - 522
[27] Carbide Tools with Nano-Dispersed Coating for High-Performance Cutting Of Hard-To-Cut Materials
Vereschaka, A. A.
Vereschaka, A. S.
Anikeev, A. I.
APPLIED MECHANICS, FLUID AND SOLID MECHANICS, 2014, 871 : 164 - +
[28] An overview on machinability of hard to cut materials using laser assisted machining
Bharat, Nikhil
Bose, P. S. C.
MATERIALS TODAY-PROCEEDINGS, 2021, 43 : 665 - 672
[29] EH10Z and EI120Z coated cemented carbides for hard-to-cut materials
Sumitomo Electric Technical Review, 1993, (35):
[30] Surface roughness analysis after laser assisted machining of hard to cut materials
Przestacki, D.
Jankowiak, M.
14TH INTERNATIONAL CONFERENCE ON METROLOGY AND PROPERTIES OF ENGINEERING SURFACES (MET & PROPS 2013), 2014, 483

← 1 2 3 4 5 →