Cryogenic machining of hard-to-cut materials

被引：251
|
作者：
Wang, ZY [1 ]
Rajurkar, KP
机构：
[1] Univ Nevada, Dept Mech Engn, Las Vegas, NV 89154 USA
[2] Univ Nebraska, Dept Ind & Management Syst Engn, Lincoln, NE 68588 USA
来源：
WEAR | 2000年 / 239卷 / 02期
关键词：
cryogenic turning; ceramics; titanium; inconel; tantalum;
D O I：
10.1016/S0043-1648(99)00361-0
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
This paper presents a technique for machining of advanced ceramics with liquid nitrogen (LN2) cooled polycrystalline cubic boron nitride (PCBN) tool, titanium alloys, Inconel alloys, and tantalum with cemented carbide tools. With LN2 cooling, the temperature in the cutting zone is reduced to a lower range, therefore, the hot-strength and hot-hardness of the tool remain high, and the temperature-dependent tool wear reduces significantly under all machining conditions. The surface roughness of all materials machined with LN2 cooling were found to be much better than the surface roughness of materials machined without LN2 cooling after the same length of cutting. (C) 2000 Elsevier Science S.A. All rights reserved.
引用
收藏
页码：168 / 175
页数：8
相关论文
共 50 条
  • [1] Precision Machining of Hard-to-Cut Materials: Current Status and Future Directions
    Cui, Tengjiao
    INTERNATIONAL JOURNAL OF ADVANCED COMPUTER SCIENCE AND APPLICATIONS, 2024, 15 (10) : 861 - 871
  • [2] Review of multi-dimensional ultrasonic vibration machining for aeronautical hard-to-cut materials
    Gao, Guofu
    Wang, Yi
    Fu, Zongxia
    Zhao, Chongyang
    Xiang, Daohui
    Zhao, Bo
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2023, 124 (3-4): : 681 - 707
  • [3] Review of multi-dimensional ultrasonic vibration machining for aeronautical hard-to-cut materials
    Guofu Gao
    Yi Wang
    Zongxia Fu
    Chongyang Zhao
    Daohui Xiang
    Bo Zhao
    The International Journal of Advanced Manufacturing Technology, 2023, 124 : 681 - 707
  • [4] More efficient grinding of hard-to-cut materials
    Mitrofanov A.P.
    Parsheva K.A.
    Mitrofanov, A.P. (greenmap@ya.ru), 1600, Allerton Press Incorporation (37): : 789 - 792
  • [5] Harmonic-based-on analysis to discriminate different mechanical actions involved in the machining of hard-to-cut materials
    Garcia-Martinez, Enrique
    Molina-Yague, Alberto
    Miguel, Valentin
    Martinez-Martinez, Alberto
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2024, 133 (1-2): : 335 - 349
  • [6] An investigation on the performance of bio-mimicked rake surface structured tool during machining of hard-to-cut materials
    Ranjan, Priya
    Hiremath, Somashekhar S.
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART E-JOURNAL OF PROCESS MECHANICAL ENGINEERING, 2023,
  • [7] Filtered cathodic vacuum Arc deposition of nano-layered composite coatings for machining hard-to-cut materials
    A. O. Volkhonskii
    A. A. Vereshchaka
    I. V. Blinkov
    A. S Vereshchaka
    A. D Batako
    The International Journal of Advanced Manufacturing Technology, 2016, 84 : 1647 - 1660
  • [8] Filtered cathodic vacuum Arc deposition of nano-layered composite coatings for machining hard-to-cut materials
    Volkhonskii, A. O.
    Vereshchaka, A. A.
    Blinkov, I. V.
    Vereshchaka, A. S.
    Batako, A. D.
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2016, 84 (5-8): : 1647 - 1660
  • [9] Experimental Study on Force of Electric Heating Drilling to Hard-to-Cut Materials
    Xu, Lanying
    Wu, Qiang
    Tang, Yong
    Qu, Gui
    Wu, Xiaodan
    MATERIALS AND MANUFACTURING PROCESSES, 2015, 30 (02) : 263 - 271
  • [10] Micromilling simulation for the hard-to-cut material
    Wang, Fei
    Cheng, Xiang
    Liu, Yuanyong
    Yang, Xianhai
    Meng, Fanjie
    13TH GLOBAL CONGRESS ON MANUFACTURING AND MANAGEMENT, 2017, 174 : 693 - 699
12345