Effect of surface finishes on ball shear strength in BGA joints with Sn-3.5 mass% Ag solder

被引：34
|
作者：
Lee, CB [1 ]
Lee, IY [1 ]
Jung, SB [1 ]
Shur, CC [1 ]
机构：
[1] Sungkyunkwan Univ, Dept Adv Mat Engn, Jangan Ku, Suwon 440746, South Korea
来源：
MATERIALS TRANSACTIONS | 2002年 / 43卷 / 04期
关键词：
ball shear test; reliability; fracture surface; ball grid array (BGA) joint; isothermal aging;
D O I：
10.2320/matertrans.43.751
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
The present Study is aimed at the assessment on the reliability of solder ball attachment to the bond pads of BGA substrate with various plating schemes. The reliability of solder ball attachment is characterized by mechanical ball shear tests. In addition to the ball shear tests, SEM is performed to inspect the cross-section and the fracture surface of the tested specimens for failure analysis. The aging was conducted in convection ovens in air at 343, 393, 423 and 443 K respectively for times ranging 8.64 x 10(4) to 864 x 10(4) s, Without regard to the deposited layer, the shear strength of BGA joints decreased with the increasing temperature and time. After isothermal aging. the fracture surface shows various characteristics depending on aging temperature and time, and the types of BGA pad.
引用
收藏
页码：751 / 756
页数：6
相关论文
共 50 条
  • [31] Interfacial reactions of Sn-3.5% Ag and Sn-3.5% Ag-0.5% Cu solder with electroless Ni/Au metallization during multiple reflow cycles
    Ahmed Sharif
    Y. C. Chan
    Journal of Materials Science: Materials in Electronics, 2005, 16 : 153 - 158
  • [32] Influence of reflow and thermal aging on the shear strength and fracture behavior of Sn-3.5Ag Solder/Cu joints
    Deng, X
    Sidhu, RS
    Johnson, P
    Chawla, N
    METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2005, 36A (01): : 55 - 64
  • [33] Influence of reflow and thermal aging on the shear strength and fracture behavior of Sn-3.5Ag solder/Cu joints
    X. Deng
    R. S. Sidhu
    P. Johnson
    N. Chawla
    Metallurgical and Materials Transactions A, 2005, 36 : 55 - 64
  • [34] Effect of in addition on Sn-Ag solder, its wetting and shear strength of copper joints
    Sebo, P
    Stefanik, P
    KOVOVE MATERIALY-METALLIC MATERIALS, 2005, 43 (03): : 202 - 209
  • [35] Effect of 0.5 wt % Cu in Sn-3.5%Ag solder on the interfacial reaction with Au/Ni metallization
    Alam, MO
    Chan, YC
    Tu, KN
    CHEMISTRY OF MATERIALS, 2003, 15 (23) : 4340 - 4342
  • [36] Mechanical properties and shear strength of Sn-3.5Ag-Bi solder alloys
    Choi, JW
    Cha, HS
    Oh, TS
    MATERIALS TRANSACTIONS, 2002, 43 (08) : 1864 - 1867
  • [37] Study on microstructure and shear strength of Sn-Ag-Sb solder joints
    Lee, HT
    Liao, TL
    Chen, MH
    ADVANCES IN ELECTRONIC MATERIALS AND PACKAGING 2001, 2001, : 315 - 322
  • [38] Comparison of Ball Pull Strength Among Various Sn-Cu-Ni Solder Joints With Different Pad Surface Finishes
    Yang, Chaoran
    Song, Fubin
    Lee, S. W. Ricky
    JOURNAL OF ELECTRONIC PACKAGING, 2014, 136 (01)
  • [39] Effect of 0.5 wt % Cu addition in Sn-3.5%Ag solder on the dissolution rate of Cu metallization
    Alam, MO
    Chan, YC
    Tu, KN
    JOURNAL OF APPLIED PHYSICS, 2003, 94 (12) : 7904 - 7909
  • [40] Effects of the melt state on the microstructure of a Sn-3.5% Ag solder at different cooling rates
    Li, Xiaoyun
    Zu, Fangqiu
    Gao, Wenlong
    Cui, Xiao
    Wang, Lifang
    Ding, Guohua
    APPLIED SURFACE SCIENCE, 2012, 258 (15) : 5677 - 5682
12345