End-Group Functionalization of Poly(3-hexylthiophene) as an Efficient Route to Photosensitize Nanocrystalline TiO2 Films for Photovoltaic Applications

被引:38
|
作者
Krueger, Robin A. [1 ]
Gordon, Terry J. [1 ]
Baumgartner, Thomas [1 ]
Sutherland, Todd C. [1 ]
机构
[1] Univ Calgary, Dept Chem, Calgary, AB T2N 1N4, Canada
基金
加拿大自然科学与工程研究理事会;
关键词
energy conversion; polythiophene; thin films; electrochemistry; mesoporous TiO2; sensitizers; SENSITIZED SOLAR-CELLS; CONJUGATED POLYMERS; ANCHORING GROUP; POLYTHIOPHENE; CATECHOL; LIGHT; RECOMBINATION; ETHYNYLENE); FABRICATION; CONVERSION;
D O I
10.1021/am200262w
中图分类号
TB3 [工程材料学];
学科分类号
0805 ; 080502 ;
摘要
Bulk heterojunction (BHJ) and dye-sensitized solar cells (DSSCs) have seen increased popularity over recent years and each technology has experienced tremendous improvements in power conversion efficiencies (PCEs), reaching 8 and 12%, respectively. The two technologies have been on independent improvement pathways, and this work establishes a link between them by using the archetypical hole conductor (poly-3-hexylthiophene, P3HT) in BHJs as a sensitizer on TiO2 for DSSC applications. Three polymers were synthesized and examined as potential TiO2 sensitizers in DSSCs under AM1.5 solar radiation. Using Grignard metathesis, regioregular P3HT was synthesized then functionalized with either one or two cyanoacrylic acid linker moieties to bind to the TiO2 surface. End-group modification resulted in minimal changes to the optical and electronic properties as compared to pristine P3HT. Cyclic voltammetry (CV) experiments at anodic potentials of adsorbed sensitizer quantified the amount of alkylthiophene adsorbed on the TiO2, whereas under reductive sweeps, cyanoacrylic acid end-group binding was determined. CVs of each polymer indicated that loading was drastically different as compared to pristine P3HT with the lowest loading on TiO2 and monofunctionalized P3HT exhibited the highest loading. The DSSCs showed power conversion efficiencies (PCEs) of 0.1%, 0.2 and 2.2% for the polymer-sensitized TiO2 of the unfunctionalized, monofunctionalized and difunctionalized polymers, respectively. DSSCs were then subjected to electrochemical impedance spectroscopy (EIS) in the dark and under monochromatic light radiation. The large variance in performance for the functionalized-P3HT sensitizers is attributed to differences in the adsorption modes of sensitizer on the TiO2 surface, which in the difunctionalized case limits electrolyte recombination and favors forward charge transfer reactions.
引用
收藏
页码:2031 / 2041
页数:11
相关论文
共 50 条
  • [31] End-group composition of poly(3-hexylthiophene)s prepared by in situ quenching of the grignard metathesis polymerization: Influence of additives and reaction conditions
    Kochemba, W. Michael
    Kilbey, S. Michael, II
    Pickel, Deanna L.
    JOURNAL OF POLYMER SCIENCE PART A-POLYMER CHEMISTRY, 2012, 50 (14) : 2762 - 2769
  • [32] Hybrid bulk heterojunction solar cells from a blend of poly(3-hexylthiophene) and TiO2 nanotubes
    Wang, Z. J.
    Qu, S. C.
    Zeng, X. B.
    Liu, J. P.
    Zhang, C. S.
    Tan, F. R.
    Jin, L.
    Wang, Z. G.
    APPLIED SURFACE SCIENCE, 2008, 255 (05) : 1916 - 1920
  • [33] Nanostructured Nanorod Arrays Presenting TiO2 Nanorods/Poly(3-hexylthiophene) for Solar Cells Application
    Wang, Hsu-Shen
    Chen, Shih-Yung
    Wang, Yuh-Lin
    Wei, Kung-Hwa
    JOURNAL OF NANOSCIENCE AND NANOTECHNOLOGY, 2011, 11 (04) : 3229 - 3234
  • [34] Enhanced performance of poly(3-hexylthiophene)-based electrochromic devices by adding a mesoporous TiO2 layer
    Baray-Calderon, A.
    Camacho-Caceres, J.
    Hernandez-Guzman, F.
    Hu, Hailin
    Nicho, M. E.
    SYNTHETIC METALS, 2023, 293
  • [35] One-step in situ hydrothermal fabrication of D/A poly(3-hexylthiophene)/TiO2 hybrid nanowires and its application in photovoltaic devices
    Chiang, Chi-Ju
    Lee, Yi-Huan
    Lee, Yu-Ping
    Lin, Guan-Ting
    Yang, Ming-Hao
    Wang, Leeyih
    Hsieh, Chih-Chen
    Dai, Chi-An
    JOURNAL OF MATERIALS CHEMISTRY A, 2016, 4 (03) : 908 - 919
  • [36] Hybrid solar cells from a blend of poly(3-hexylthiophene) and ligand-capped TiO2 nanorods
    Boucle, Johann
    Chyla, Sabina
    Shaffer, Milo S. P.
    Durrant, James R.
    Bradley, Donal D. C.
    Nelson, Jenny
    ADVANCED FUNCTIONAL MATERIALS, 2008, 18 (04) : 622 - 633
  • [37] Hybrid solar cells based on poly(3-hexylthiophene) and electrospun TiO2 nanofibers with effective interface modification
    Tai, Qidong
    Zhao, Xingzhong
    Yan, Feng
    JOURNAL OF MATERIALS CHEMISTRY, 2010, 20 (35) : 7366 - 7371
  • [38] Hybrid solar cells based on poly(3-hexylthiophene) and electrospun TiO2 nanofibers modified with CdS nanoparticles
    Shingchung Lo
    Zhike Liu
    Jinhua Li
    Helen Laiwa Chan
    Feng Yan
    Progress in Natural Science:Materials International, 2013, 23 (05) : 514 - 518
  • [39] Influence of solvent on film morphology and device performance of poly(3-hexylthiophene):TiO2 nanocomposite solar cells
    Kwong, CY
    Djurisic, AB
    Chui, PC
    Cheng, KW
    Chan, WK
    CHEMICAL PHYSICS LETTERS, 2004, 384 (4-6) : 372 - 375
  • [40] Hybrid solar cells based on poly(3-hexylthiophene) and electrospun TiO2 nanofibers modified with CdS nanoparticles
    Lo, Shingchung
    Liu, Zhike
    Li, Jinhua
    Chan, Helen Laiwa
    Yan, Feng
    PROGRESS IN NATURAL SCIENCE-MATERIALS INTERNATIONAL, 2013, 23 (05) : 514 - 518