FRACTURE TOUGHNESS OF X70 PIPE GIRTH WELDS USING CLAMPED SE(T) AND SE(B) SINGLE-SPECIMENS

被引：0

作者：

Park, Dong-Yeob ^{[1
]}

Gravel, Jean-Philippe ^{[1
]}

Simha, C. Hari Manoj ^{[2
]}

Liang, Jie ^{[2
]}

Duan, Da-Ming ^{[3
]}

机构：

[1] Nat Resources Canada, CanmetMAT, Calgary, AB, Canada

[2] Nat Resources Canada, CanmetMAT, Hamilton, ON, Canada

[3] TransCanada, Calgary, AB, Canada

来源：

PROCEEDINGS OF THE 10TH INTERNATIONAL PIPELINE CONFERENCE - 2014, VOL 4 | 2014年

关键词：

D O I：

暂无

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Shallow-notched single edge -notched tension (SE(T) or SENT) and deep-and shallow -notched single edge -notched bend (SE(B) or SENB) specimens with notches positioned in the weld and the heat-affected zone were tested. Crack-tip opening displacement (CTOD) versus resistance curves were obtained using both a single and double clip gauge consolidated in a SE(T) single-specimen. Up until the peak load the resistance curves from both gauging methods yield approximately the same results; thereafter the curves deviate. Interrupted testing showed that the crack had initiated below 50% of the peak load, and in some cases had propagated significantly prior to reaching the peak load.

引用

页数：7

共 50 条

[21] Low constraint fracture toughness testing for master curve reference temperature determination using 10 mm-thick SE(B) and SE(T) specimens
Lindqvist, Sebastian
Forsstrom, Antti
Veijola, Timo
Collins, William
ENGINEERING FRACTURE MECHANICS, 2024, 310
[22] EFFECT OF CHEMISTRY ON THE FRACTURE TOUGHNESS OF LOW CARBON X70 GIRTH WELD HEAT AFFECTED ZONE
Rashid, M.
Collins, L. E.
Bian, Y.
PROCEEDINGS OF THE 10TH INTERNATIONAL PIPELINE CONFERENCE - 2014, VOL 3, 2014,
[23] Crack tunneling effects on the elastic unloading compliance of C(T), SE(B) and clamped SE(T) specimens and correction methodology
Andrade, L. G. F.
Neto, M. Mattar
Donato, G. H. B.
THEORETICAL AND APPLIED FRACTURE MECHANICS, 2023, 125
[24] EFFECTS OF WELD STRENGTH MISMATCH ON ESTIMATION PROCEDURES FOR J FRACTURE PARAMETER USING CLAMPED SE(T) SPECIMENS
Donato, Gustavo H. B.
Magnabosco, Rodrigo
Ruggieri, Claudio
ASME PRESSURE VESSELS AND PIPING CONFERENCE 2009, VOL 3: DESIGN AND ANALYSIS, 2010, : 517 - 526
[25] Experimental investigation of out-of -planeconstraint effect on fracture toughness of the SE(T) specimens
Li Yizhe
Gong Baoming
Corrado, Mauro
Deng Caiyan
Wang Dongpo
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 2017, 128 : 644 - 651
[26] Validity limits of the one-parameter elastic-plastic fracture mechanics (J-integral) considering SE(B), C(T) and clamped SE(T) specimens
Bolognesi Donato, Gustavo Henrique
Moreira, Felipe Cavalheiro
ECF22 - LOADING AND ENVIRONMENTAL EFFECTS ON STRUCTURAL INTEGRITY, 2018, 13 : 1879 - 1887
[27] J-Q AND TOUGHNESS SCALING MODEL SOLUTIONS FOR M(T), DE(T), SE(B), SE(T) AND C(T) SPECIMENS
GULLERUD, AS
DODDS, RH
INTERNATIONAL JOURNAL OF FRACTURE, 1995, 72 (01) : R11 - R21
[28] Integrity assessment of API X70 pipe with corroded girth and seam welds via numerical simulation and burst test experiments
Yeom, Kyu Jung
Kim, Woo Sik
Oh, Kyu Hwan
ENGINEERING FAILURE ANALYSIS, 2016, 70 : 375 - 386
[29] ESTIMATION PROCEDURES FOR J AND CTOD FRACTURE PARAMETERS EXPERIMENTAL EVALUATION USING HOMOGENEOUS AND MISMATCHED CLAMPED SE(T) SPECIMENS
Moreira, Felipe C.
Donato, Gustavo H. B.
PROCEEDINGS OF THE ASME PRESSURE VESSELS AND PIPING CONFERENCE 2010, VOL 3, 2010, : 711 - 720
[30] Fracture-Toughness Evaluation in Submerged Arc-Welding Seam Welds in Nonstandard Curved SE(B) Specimens in the Short Radial Direction of API 5L Steel Pipe
Angeles-Herrera, D.
Gonzalez-Velazquez, J.
de Morales-Ramirez, A. J.
JOURNAL OF TESTING AND EVALUATION, 2012, 40 (06) : 886 - 889

← 1 2 3 4 5 →