Mechanical properties of Ti3AlC2 ceramics before and after heat treatment

被引：1
|
作者：
Yao, Lei [1 ]
Zhu, Chun-Cheng [1 ]
Jiang, Jiu-Xing [2 ]
Zhou, Bai-Bin [1 ]
机构：
[1] Harbin Normal Univ, Key Lab Design & Synth Funct Mat & Green Catalysi, Harbin 150025, Peoples R China
[2] Harbin Univ Sci & Technol, Coll Appl Sci, Harbin 150080, Peoples R China
来源：
RARE METALS | 2022年 / 41卷 / 08期
基金：
中国国家自然科学基金;
关键词：
Ti3AlC2; Heat treatment; Mechanical properties; PHASES; EVOLUTION; DAMAGE;
D O I：
10.1007/s12598-015-0609-z
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Ti3AlC2 ceramics were heat treated at the temperature from 1050 to 1450 degrees C. Vickers hardness, fracture toughness, flexural strength and compressive strength of Ti3AlC2 were tested and calculated before and after heat treatment, respectively. Ti3AlC2 content, fracture toughness, flexural strength and compressive strength of Ti3AlC2 first increase and then decrease, while Vickers hardness is just the opposite with the increase in temperature from 1050 to 1450 degrees C. After heat treatment at 1250 degrees C, Ti3AlC2 content reaches the highest level of 94.2 wt%, and fracture toughness, flexural strength and compressive strength reach the maximum values, which are 6.4 MPa center dot m(1/2), 318 MPa and 662 MPa, respectively. Vickers hardness reduces to the lowest value of 2.9 GPa. Heat treatment does improve the strength and Ti3AlC2 content, but reduces the hardness and optimizes the mechanical properties of Ti3AlC2.
引用
收藏
页码：2777 / 2782
页数：6
相关论文
共 50 条
  • [21] Preparation of Ti3AlC2 materials by mechanically alloying and heat treatment
    Liang, Bao-Yan
    Wang, Ming-Zhi
    Wang, Lei
    Fenmo Yejin Cailiao Kexue yu Gongcheng/Materials Science and Engineering of Powder Metallurgy, 2012, 17 (03): : 327 - 332
  • [22] Improvement in the mechanical properties of plasma spray ceramic-Cu/TI3AlC2 gradient coatings by heat treatment
    Li, Qiaolei
    Song, Peng
    Huang, Wenlang
    Deng, Chunming
    Wang, Chunjian
    Li, Lu
    Zheng, Biju
    Lu, Jiansheng
    CERAMICS INTERNATIONAL, 2019, 45 (17) : 22452 - 22463
  • [23] Additive Manufacturing of Ti3AlC2/TiC and Ti3AlC2/SiC Ceramics Using the Fused Granules Fabrication Technique
    Krinitcyn, Maksim
    Kopytov, Georgy
    Ryumin, Egor
    JOURNAL OF MANUFACTURING AND MATERIALS PROCESSING, 2024, 8 (03):
  • [24] Physical, mechanical, and ablation properties of Cu-Ti3AlC2 composites with various Ti3AlC2 contents
    Huang, Xiaochen
    Feng, Yi
    Qian, Gang
    Zhao, Hao
    Zhang, Jingcheng
    Zhang, Xuebin
    MATERIALS SCIENCE AND TECHNOLOGY, 2018, 34 (06) : 757 - 762
  • [25] Influence of selective laser treatment on thermal stability of Ti3AlC2 and Ti3AlC2/Cu powders
    Krinitcyn, M.
    Ragulina, M.
    Firsina, I
    Travitzky, N.
    MATERIALS LETTERS, 2022, 309
  • [26] Pressureless Sintering and Properties of Ti3AlC2
    Lu, Xinpo
    Zhou, Yanchun
    INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY, 2010, 7 (06) : 744 - 751
  • [27] Electronic structures and bonding properties of Ti2AlC and Ti3AlC2
    Min Xinmin
    Yi, Ren
    JOURNAL OF WUHAN UNIVERSITY OF TECHNOLOGY-MATERIALS SCIENCE EDITION, 2007, 22 (01): : 27 - 30
  • [28] Layered Machinable and Electrically Conductive Ti2AlC and Ti3AlC2 Ceramics: a Review
    Wang, X. H.
    Zhou, Y. C.
    JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2010, 26 (05) : 385 - 416
  • [29] Electronic Structures and Bonding Properties of Ti2AlC and Ti3AlC2
    闵新民
    Journal of Wuhan University of Technology(Materials Science Edition), 2007, (01) : 27 - 30
  • [30] Layered Machinable and Electrically Conductive Ti2AlC and Ti3AlC2 Ceramics:a Review
    X.H.Wang and Y.C.Zhou Shenyang National Laboratory for Materials Science
    JournalofMaterialsScience&Technology, 2010, 26 (05) : 385 - 416
12345