THE INFLUENCE OF INJECTION TIME AND HOLDING TIME ON THE RESIDUAL STRESS STATE IN INJECTION MOULDED PARTS

被引：1

作者：

Jaruga, Tomasz ^{[1
]}

Mazik, Katarzyna ^{[1
]}

机构：

[1] Politech Czestochowska, Inst Technol Mech, Zaklad Przetworstwa Polimerow, PL-42201 Czestochowa, Poland

来源：

POLIMERY | 2013年 / 58卷 / 7-8期

关键词：

injection moulding; residual stress; photoelastic investigation; injection time; holding time; SHRINKAGE;

D O I：

10.14314/polimery.2013.587

中图分类号：

O63 [高分子化学（高聚物）];

学科分类号：

070305 ; 080501 ; 081704 ;

摘要：

The requirements for the manufacturing process of transparent parts by injection moulding were described. Special attention was paid to such processing parameters like injection time and holding time, which are essential for the production of good quality parts. The effect of these parameters on the residual stress in (methyl methacrylate)-acrylonitrile-butadiene-styrene plastic (MABS) injection moulded parts was investigated using photoelastic analysis.

引用

页码：587 / 596

页数：10

共 50 条

[31] Cost analysis in injection moulded plastic parts designing
Turc, C. G.
Carausu, C.
Belgiu, G.
MODTECH INTERNATIONAL CONFERENCE - MODERN TECHNOLOGIES IN INDUSTRIAL ENGINEERING V, 2017, 227
[32] DEVELOPMENTS IN SINTERING INJECTION MOULDED PM PARTS.
Kennedy, Sheldon W.
Metal Powder Report, 1987, 42 (09) : 609 - 611
[33] Programs for the Rheological Design of Injection Moulded Parts.
Malz, Juergen
Plastverarbeiter, 1988, 39 (05): : 16 - 26
[34] Technical injection moulded parts from foamed thermoplastics
Technische Spritzgussteile aus geschaeumten Thermoplasten
Hausch, Joachim, 1600, (123):
[35] Residual stress and warpage models for complex injection molded parts
Young, WB
Wang, J
INTERNATIONAL POLYMER PROCESSING, 2002, 17 (03) : 271 - 278
[36] Polymer based injection mould cavity inserts: An influence on crystallization and thermo-mechanical properties of injection moulded parts
Češková M.
Lenfeld P.
Materials Science Forum, 2020, 994 : 143 - 151
[37] Influence of Metal Powder Reinforced Polymer Composite on the Mechanical Properties of Injection Moulded Parts
Raut, Sandeep, V
Bongale, Arunkumar
Kumar, Satish
Bongale, Anupkumar
INTERNATIONAL CONFERENCE ON SMART SUSTAINABLE MATERIALS AND TECHNOLOGIES (ICSSMT-2020), 2020, 2297
[38] Laser Transmission Welding of Foamed Thermoplastic Injection Moulded Parts
Hopmann, Christian
Kreimeier, Suveni
Schoengart, Maximilian
PROCEEDINGS OF PPS-32: THE 32ND INTERNATIONAL CONFERENCE OF THE POLYMER PROCESSING SOCIETY, 2017, 1914
[39] Comparison of similar injection moulded parts by a coordinate measuring machine
Samir Lemes
SN Applied Sciences, 2019, 1
[40] Powder-binder separation in injection moulded green parts
Mannschatz, Anne
Hoehn, Soeren
Moritz, Tassilo
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY, 2010, 30 (14) : 2827 - 2832

← 1 2 3 4 5 →