THE INFLUENCE OF INJECTION TIME AND HOLDING TIME ON THE RESIDUAL STRESS STATE IN INJECTION MOULDED PARTS

被引：1
|
作者：
Jaruga, Tomasz [1 ]
Mazik, Katarzyna [1 ]
机构：
[1] Politech Czestochowska, Inst Technol Mech, Zaklad Przetworstwa Polimerow, PL-42201 Czestochowa, Poland
来源：
POLIMERY | 2013年 / 58卷 / 7-8期
关键词：
injection moulding; residual stress; photoelastic investigation; injection time; holding time; SHRINKAGE;
D O I：
10.14314/polimery.2013.587
中图分类号：
O63 [高分子化学（高聚物）];
学科分类号：
070305 ; 080501 ; 081704 ;
摘要：
The requirements for the manufacturing process of transparent parts by injection moulding were described. Special attention was paid to such processing parameters like injection time and holding time, which are essential for the production of good quality parts. The effect of these parameters on the residual stress in (methyl methacrylate)-acrylonitrile-butadiene-styrene plastic (MABS) injection moulded parts was investigated using photoelastic analysis.
引用
收藏
页码：587 / 596
页数：10
相关论文
共 50 条
  • [21] Infl uence of the EFE injection system on cure time reduction and properties of moulded parts - Part 2
    Einfluss des EFE-Spritzsystems auf Heizzeitreduzierung und Eigenschaften der gespritzten Bauteile: Teil 2: Einfluss der Verfahrensparameter des Spritzgießprozesses auf die Heizzeitreduzierung
    1600, Dr. Gupta Verlag, P.O. Box 104125, Ratingen, D-40852, Germany (66):
  • [22] Infl uence of the EFE injection system on cure time reduction and properties of moulded parts - Part 3
    Herrmann, V.
    Naß, F.
    Lemmich, S.
    Wachter, F.
    Riedelbauch, Heinz
    Gummi, Fasern, Kunststoffe, 2013, 66 (03): : 180 - 184
  • [23] Influence of Rapid Mould Temperature Variation on the Appearance of Injection-Moulded Parts
    Lucchetta, Giovanni
    Fiorotto, Marco
    STROJNISKI VESTNIK-JOURNAL OF MECHANICAL ENGINEERING, 2013, 59 (11): : 683 - 688
  • [24] Calculations of the flow-induced residual stress development in the injection moulded plate
    Chen, Shia-Chung
    Chen, Yung-Cheng
    Computers and Structures, 1994, 52 (05): : 1043 - 1050
  • [25] Influence of residual stresses on the mechanical and thermal properties of injection moulded ABS copolymer
    Univ of Ulster at Jordanstown, United Kingdom
    J Mater Sci, 13 (3358-3368):
  • [26] Short-fibre-reinforced injection moulded parts
    Mlekusch, B
    KUNSTSTOFFE-PLAST EUROPE, 1999, 89 (07): : 33 - +
  • [27] Mesoscale simulation of the solidification process in injection moulded parts
    Spekowius, Marcel
    Spina, Roberto
    Hopmann, Christian
    JOURNAL OF POLYMER ENGINEERING, 2016, 36 (06) : 563 - 573
  • [28] Quality control of injection moulded micro mechanical parts
    Gasparin, S.
    Tosello, G.
    Hansen, H. N.
    Jorgensen, M. B.
    4M/ICOMM 2009 - THE GLOBAL CONFERENCE ON MICRO MANUFACTURE, 2009, : 175 - 178
  • [29] Investigation of inserts surface structures on injection moulded parts
    Kun, Krisztian
    Boza, Pal
    XXIII INTERNATIONAL CONFERENCE ON MANUFACTURING (MANUFACTURING 2018), 2018, 448
  • [30] Production-grade injection moulded parts in days
    Palmer, Dean
    Eureka, 2006, 26 (03)
12345