Influence of custom-made and prefabricated insoles before and after an intense run

被引:19
|
作者
Gabriel Lucas-Cuevas, Angel [1 ]
Camacho-Garcia, Andres [2 ]
Llinares, Raul [2 ]
Priego Quesada, Jose Ignacio [1 ,3 ]
Llana-Belloch, Salvador [1 ]
Perez-Soriano, Pedro [1 ]
机构
[1] Univ Valencia, Dept Phys Educ & Sports, Res Grp Sport Biomech GIBD, Valencia, Spain
[2] Univ Politecn Valencia, Alcoy, Spain
[3] Univ Valencia, Dept Physiol, Biophys & Med Phys Grp, Valencia, Spain
来源
PLOS ONE | 2017年 / 12卷 / 02期
关键词
TIBIAL STRESS-FRACTURE; GROUND REACTION FORCE; SHOCK ATTENUATION; LOWER-EXTREMITY; IMPACT FORCES; PERCEIVED EXERTION; MIDSOLE THICKNESS; OVERUSE INJURIES; PLANTAR PRESSURE; STRIKE PATTERN;
D O I
10.1371/journal.pone.0173179
中图分类号
O [数理科学和化学]; P [天文学、地球科学]; Q [生物科学]; N [自然科学总论];
学科分类号
07 ; 0710 ; 09 ;
摘要
Each time the foot contacts the ground during running there is a rapid deceleration that results in a shock wave that is transmitted from the foot to the head. The fatigue of the musculoskeletal system during running may decrease the ability of the body to absorb those shock waves and increase the risk of injury. Insoles are commonly prescribed to prevent injuries, and both custom-made and prefabricated insoles have been observed to reduce shock accelerations during running. However, no study to date has included a direct comparison of their behaviour measured over the same group of athletes, and therefore great controversy still exists regarding their effectiveness in reducing impact loading during running. The aim of the study was to analyse the acute differences in stride and shock parameters while running on a treadmill with custom-made and prefabricated insoles. Stride parameters (stride length, stride rate) and shock acceleration parameters (head and tibial peak acceleration, shock magnitude, acceleration rate, and shock attenuation) were measured using two triaxial accelerometers in 38 runners at 3.33 m/s before and after a 15-min intense run while using the sock liner of the shoe (control condition), prefabricated insoles and custom-made insoles. No differences in shock accelerations were found between the custom-made and the control insoles. The prefabricated insoles increased the head acceleration rate (post-fatigue, p = 0.029) compared to the control condition. The custom-made reduced tibial (pre-fatigue, p = 0.041) and head acceleration rates (pre-fatigue and post-fatigue, p = 0.01 and p = 0.046) compared to the prefabricated insoles. Neither the stride nor the acceleration parameters were modified as a result of the intense run. In the present study, the acute use of insoles (custom-made, prefabricated) did not reduce shock accelerations compared to the control insoles. Therefore, their effectiveness at protecting against injuries associated with elevated accelerations is not supported and remains unclear.
引用
收藏
页数:14
相关论文
共 50 条
  • [41] Custom-Made Ethyl Vinyl Acetate Insoles with Arch Support Could Improve Static Balance in Diabetic Women with Neuropathic Foot
    Hemmati, Fatemeh
    Tafti, Nahid
    Nourouzi, Ehsan
    Turk, Sajad Bayat
    Karimi, Mohammad Taghi
    Sharifmoradi, Keyvan
    Kashani, Reza Vahab
    JOURNAL OF THE AMERICAN PODIATRIC MEDICAL ASSOCIATION, 2023, 113 (03)
  • [42] Influence of custom-made mouth guards on strength, speed and anaerobic performance of taekwondo athletes
    Cetin, Cem
    Kececi, Ayse Diljin
    Erdogan, Ali
    Baydar, Metin Luetfi
    DENTAL TRAUMATOLOGY, 2009, 25 (03) : 272 - 276
  • [43] Factors that Influence the Adoption of Information Security on Requirement Phase for Custom-Made Software at SMEs
    Alghamdi, Fatimah
    Hamza, Nermin
    Tamimi, Moutasm
    2019 2ND INTERNATIONAL CONFERENCE ON COMPUTER APPLICATIONS & INFORMATION SECURITY (ICCAIS), 2019,
  • [44] Efficacy of custom-made pressure clips for ear keloid treatment after surgical excision
    Tanaydin, V.
    Beugels, J.
    Piatkowski, A.
    Colla, C.
    van den Kerckhove, E.
    Hugenholtz, G. C. G.
    van der Hulst, R. R.
    JOURNAL OF PLASTIC RECONSTRUCTIVE AND AESTHETIC SURGERY, 2016, 69 (01): : 115 - 121
  • [45] Custom-Made Nasal Retainer Using Latex Nelaton Urine Catheter After the Cheiloplasty
    Oh, Joon Seok
    Chung, Jeehyeok
    Ha, Jeong Hyun
    Yoo, Hyo Kyung
    Kim, Sukwha
    CLEFT PALATE-CRANIOFACIAL JOURNAL, 2021, 58 (11): : 1443 - 1445
  • [46] Secondary Interventions After Custom-Made Iliac Branched Devices in Severe Iliac Tortuosity
    Lauret, Gert-Jan
    Dijkema, Elles
    Smeets, Reinier
    JOURNAL OF VASCULAR SURGERY, 2024, 79 (04) : 12S - 12S
  • [47] In Vitro Fracture Resistance of Endodontically Treated Premolar Teeth Restored with Prefabricated and Custom-Made Fibre-Reinforced Composite Posts
    Bialy, Michal
    Targonska, Sara
    Szust, Agnieszka
    Wiglusz, Rafal J.
    Dobrzynski, Maciej
    MATERIALS, 2021, 14 (20)
  • [48] Influence of Different CAD/CAM Crown Materials on the Fracture of Custom-Made Titanium and Zirconia Implant Abutments After Artificial Aging
    Elsayed, Adham
    Farrag, Gasser
    Chaar, Mohamed Sad
    Abdelnabi, Nouran
    Kern, Matthias
    INTERNATIONAL JOURNAL OF PROSTHODONTICS, 2019, 32 (01) : 91 - 96
  • [49] Intervention study to improve quality of life and health problems of community-living elderly women in Japan by shoe fitting and custom-made insoles
    Kusumoto, Ayano
    Suzuki, Takao
    Yoshida, Hideyo
    Kwon, Jinhee
    GERONTOLOGY, 2007, 53 (06) : 348 - 356
  • [50] Sternal replacement with a custom-made titanium plate after resection of a solitary breast cancer metastasis
    Demondion, Pierre
    Mercier, Olaf
    Kolb, Frederic
    Fadel, Elie
    INTERACTIVE CARDIOVASCULAR AND THORACIC SURGERY, 2014, 18 (01) : 145 - 147