Influence of Protective Coatings of Inserts on Cutting Forces during Milling of Hadfield Steel

被引：1
|
作者：
Pyatykh, A. S. [1 ]
Savilov, A. V. [1 ]
Timofeev, S. A. [1 ]
Svinin, V. M. [1 ]
Maizel, I. G. [1 ]
机构：
[1] Irkutsk Natl Res Tech Univ, Irkutsk 664074, Russia
来源：
JOURNAL OF FRICTION AND WEAR | 2023年 / 44卷 / 03期
关键词：
Hadfield steel; milling; cutting forces; coefficient of friction; Taguchi method; analysis of variance; regression analysis; protective coatings; cutting modes; hard alloy; SURFACE-ROUGHNESS; OPTIMIZATION; OPERATION;
D O I：
10.3103/S1068366623030078
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
The present study analyzed the effect of protective coatings of replaceable hard-alloy plates on cutting forces when milling austenitic high-manganese Hadfield (110G13L) steel. S30T, 1130, S40T, and 4240 hard alloys with PVD and CVD coatings were explored. The analysis was conducted on a milling machining center with a dynamometer plate installed on the table. The experiment was based on the orthogonal planning matrix. The Taguchi method was employed to identify a coating with the best properties. The analysis of variance showed that the tool feed has the greatest effect on active cutting forces. The specific feed gravity was 65.22%. The regression analysis revealed that to minimize and predict cutting forces for the entire range of cutting conditions, S30T alloy with a protective TiAlN PVD coating is preferable in machining austenitic 110G13L stainless steel. The results can improve the machining efficiency for Hadfield steel products produced by machine-building enterprises.
引用
收藏
页码：156 / 163
页数：8
相关论文
共 50 条
  • [1] Influence of Protective Coatings of Inserts on Cutting Forces during Milling of Hadfield Steel
    A. S. Pyatykh
    A. V. Savilov
    S. A. Timofeev
    V. M. Svinin
    I. G. Maizel
    Journal of Friction and Wear, 2023, 44 : 156 - 163
  • [2] THE WEAR TESTS OF CUTTING INSERTS WITH DIFFERENT COATINGS DURING A MILLING PROCESS
    Maj, Piotr
    Miko, Edward
    METAL 2017: 26TH INTERNATIONAL CONFERENCE ON METALLURGY AND MATERIALS, 2017, : 1367 - 1371
  • [3] Influence of the Number of Inserts Used for Face Milling on Cutting Forces and Surface Roughness
    Horava, Cyril
    Reznicek, Martin
    Ovsik, Martin
    Materials, 2024, 17 (24)
  • [4] Milling behavior of Hadfield steel with cryogenically treated tungsten carbide inserts
    Ekici, Ergun
    MATERIALS TESTING, 2015, 57 (11-12) : 968 - 976
  • [5] STUDY ON THE CUTTING FORCES DURING FACE MILLING OF A HARD STEEL
    Malea, Claudiu Ionut
    Nitu, Eduard Laurentiu
    Badulescu, Claudiu
    Iordache, Daniela Monica
    ACTA TECHNICA NAPOCENSIS SERIES-APPLIED MATHEMATICS MECHANICS AND ENGINEERING, 2023, 66 (05): : 451 - 460
  • [6] Modeling Static Cutting Forces And Stresses in the Face Milling Inserts
    Kyung, Richard
    Yim, Jesang
    2020 IEEE INTERNATIONAL IOT, ELECTRONICS AND MECHATRONICS CONFERENCE (IEMTRONICS 2020), 2020, : 557 - 560
  • [7] The influence of cutting forces on surface roughness in the milling of curved hardened steel surfaces
    Kull Neto, Henrique
    Diniz, Anselmo Eduardo
    Pederiva, Robson
    International Journal of Advanced Manufacturing Technology, 2016, 84 (5-8): : 1209 - 1218
  • [8] The influence of cutting forces on surface roughness in the milling of curved hardened steel surfaces
    Henrique Kull Neto
    Anselmo Eduardo Diniz
    Robson Pederiva
    The International Journal of Advanced Manufacturing Technology, 2016, 84 : 1209 - 1218
  • [9] The influence of cutting forces on surface roughness in the milling of curved hardened steel surfaces
    Kull Neto, Henrique
    Diniz, Anselmo Eduardo
    Pederiva, Robson
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2016, 84 (5-8): : 1209 - 1218
  • [10] Cutting Forces Analysis During High Speed Milling of Hardened Tool Steel
    Abdulgadir, Mustafa M.
    MODERN METHODS OF CONSTRUCTION DESIGN, 2014, : 549 - 555
12345