Influence of Protective Coatings of Inserts on Cutting Forces during Milling of Hadfield Steel

被引：1
|
作者：
Pyatykh, A. S. [1 ]
Savilov, A. V. [1 ]
Timofeev, S. A. [1 ]
Svinin, V. M. [1 ]
Maizel, I. G. [1 ]
机构：
[1] Irkutsk Natl Res Tech Univ, Irkutsk 664074, Russia
来源：
JOURNAL OF FRICTION AND WEAR | 2023年 / 44卷 / 03期
关键词：
Hadfield steel; milling; cutting forces; coefficient of friction; Taguchi method; analysis of variance; regression analysis; protective coatings; cutting modes; hard alloy; SURFACE-ROUGHNESS; OPTIMIZATION; OPERATION;
D O I：
10.3103/S1068366623030078
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
The present study analyzed the effect of protective coatings of replaceable hard-alloy plates on cutting forces when milling austenitic high-manganese Hadfield (110G13L) steel. S30T, 1130, S40T, and 4240 hard alloys with PVD and CVD coatings were explored. The analysis was conducted on a milling machining center with a dynamometer plate installed on the table. The experiment was based on the orthogonal planning matrix. The Taguchi method was employed to identify a coating with the best properties. The analysis of variance showed that the tool feed has the greatest effect on active cutting forces. The specific feed gravity was 65.22%. The regression analysis revealed that to minimize and predict cutting forces for the entire range of cutting conditions, S30T alloy with a protective TiAlN PVD coating is preferable in machining austenitic 110G13L stainless steel. The results can improve the machining efficiency for Hadfield steel products produced by machine-building enterprises.
引用
收藏
页码：156 / 163
页数：8
相关论文
共 50 条
  • [21] The Influence of Milling Parameters on Cutting Forces in High-Speed Milling of Polymer Materials
    Uysal, Alper
    Dzhemilov, Eshreb
    Dzhemalyadinov, Ruslan
    ADVANCES IN DESIGN, SIMULATION AND MANUFACTURING III: MANUFACTURING AND MATERIALS ENGINEERING, VOL 1, 2020, : 462 - 470
  • [22] Comparison of the steel-milling performance of carbide inserts with MTCVD and PVD TiCN coatings
    Santhanam, AT
    Quinto, DT
    Grab, GP
    INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS, 1996, 14 (1-3): : 31 - 40
  • [23] Influence of cutting edge radius on the wear resistance of PM-HSS milling inserts
    Rech, J
    Yen, YC
    Schaff, MJ
    Hamdi, H
    Altan, T
    Bouzakis, KD
    WEAR, 2005, 259 : 1168 - 1176
  • [24] Optimization of cutting parameters during CNC milling of EN24 steel with Tungsten carbide coated inserts: A critical review
    Patil, Shashwath
    Rao, P. Sudhakar
    Prabhudev, M. S.
    Khan, Mohd Yunus
    Anjaiah, G.
    MATERIALS TODAY-PROCEEDINGS, 2022, 62 : 3213 - 3220
  • [25] ExPERIMENTAL AND NUMERICAL INvESTIGATION OF CUTTING FORCES AND TEMPERATURES IN MILLING OF CUSTOM 450 STEEL
    Gokce, Harun
    ARCHIVES OF METALLURGY AND MATERIALS, 2022, 67 (03) : 843 - 853
  • [26] Influence of Surface Layer Condition of Al2O3+TiC Ceramic Inserts on Quality of Deposited Coatings and Reliability during Hardened Steel Milling
    Volosova, Marina A.
    Stebulyanin, Mikhail M.
    Gurin, Vladimir D.
    Melnik, Yury A.
    COATINGS, 2022, 12 (12)
  • [27] Influence of preheating on performance of circular carbide inserts in end milling of carbon steel
    Amin, A. K. M. Nurul
    Abraham, Irwan
    Khairusshima, Nor
    Ahmed, Mirghani I.
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2007, 185 (1-3) : 97 - 105
  • [28] Study of cutting forces for milling plain carbon steel using chamfered main cutting edge tools
    Chang, Chung-Shin
    American Society of Mechanical Engineers, Manufacturing Engineering Division, MED, 1999, 10 : 243 - 252
  • [29] Prediction of cutting forces for the milling of plain carbon steel using chamfered main cutting edge tools
    Chang, CS
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2000, 105 (03) : 302 - 326
  • [30] THE USE OF CARBIDE INSERTS WITH WEAR-RESISTANT COATINGS FOR THE FACE MILLING OF STRUCTURAL-STEEL
    KLUSHIN, MI
    SOVIET ENGINEERING RESEARCH, 1985, 5 (03): : 65 - 67
12345