Influence of Protective Coatings of Inserts on Cutting Forces during Milling of Hadfield Steel

被引：1

作者：

Pyatykh, A. S. ^{[1
]}

Savilov, A. V. ^{[1
]}

Timofeev, S. A. ^{[1
]}

Svinin, V. M. ^{[1
]}

Maizel, I. G. ^{[1
]}

机构：

[1] Irkutsk Natl Res Tech Univ, Irkutsk 664074, Russia

来源：

JOURNAL OF FRICTION AND WEAR | 2023年 / 44卷 / 03期

关键词：

Hadfield steel; milling; cutting forces; coefficient of friction; Taguchi method; analysis of variance; regression analysis; protective coatings; cutting modes; hard alloy; SURFACE-ROUGHNESS; OPTIMIZATION; OPERATION;

D O I：

10.3103/S1068366623030078

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

The present study analyzed the effect of protective coatings of replaceable hard-alloy plates on cutting forces when milling austenitic high-manganese Hadfield (110G13L) steel. S30T, 1130, S40T, and 4240 hard alloys with PVD and CVD coatings were explored. The analysis was conducted on a milling machining center with a dynamometer plate installed on the table. The experiment was based on the orthogonal planning matrix. The Taguchi method was employed to identify a coating with the best properties. The analysis of variance showed that the tool feed has the greatest effect on active cutting forces. The specific feed gravity was 65.22%. The regression analysis revealed that to minimize and predict cutting forces for the entire range of cutting conditions, S30T alloy with a protective TiAlN PVD coating is preferable in machining austenitic 110G13L stainless steel. The results can improve the machining efficiency for Hadfield steel products produced by machine-building enterprises.

引用

页码：156 / 163

页数：8

共 50 条

[31] Influence of cutting parameters on cutting forces in high speed milling of thin walled graphite electrode
Hu Zhouling
Wang Chengyong
Zhou Li
Fu Hao
PROGRESS OF MACHINING TECHNOLOGY, PROCEEDINGS, 2006, : 341 - 344
[32] Online detection and analysis of cutting forces during the milling process with robots
Bliedtner, J.
Moeller, K.
Annals of DAAAM for 2006 & Proceedings of the 17th International DAAAM Symposium: INTELLIGENT MANUFACTURING & AUTOMATION: FOCUS ON MECHATRONICS AND ROBOTICS, 2006, : 41 - 42
[33] Characteristic variations of chip morphology and cutting forces in face milling with flat-faced and grooved tool inserts
Fang, N
JSME INTERNATIONAL JOURNAL SERIES A-SOLID MECHANICS AND MATERIAL ENGINEERING, 2003, 46 (03) : 230 - 236
[34] Cutting Forces during Inconel 718 Orthogonal Turn-Milling
Felusiak-Czyryca, Agata
Madajewski, Marek
Twardowski, Pawel
Wiciak-Pikula, Martyna
MATERIALS, 2021, 14 (20)
[35] Cutting forces and vibrations during ball end milling of inclined surfaces
Wojciechowski, Szymon
Twardowski, Pawel
Pelic, Marcin
6TH CIRP INTERNATIONAL CONFERENCE ON HIGH PERFORMANCE CUTTING (HPC2014), 2014, 14 : 113 - 118
[36] Comparative wear behavior studies of coated inserts during milling of NiCrMoV steel
Oomen-Hurst, S.
Abad, M. D.
Khanna, M.
Veldhuis, S. C.
TRIBOLOGY INTERNATIONAL, 2012, 53 : 115 - 123
[37] Influence of Wear-Resistant Coating on the Reliability of Replaceable Inserts in Cutting Steel
Zhang, J.
Kozlov, V. N.
Liu, S.
INTERNATIONAL CONFERENCE ON MECHANICAL ENGINEERING AND MODERN TECHNOLOGIES 2019 (MEMT2019), 2020, 795
[38] The influence of feed rate and cutting speed on the cutting forces, surface roughness and tool-chip contact length during face milling
Korkut, I.
Donertas, M. A.
MATERIALS & DESIGN, 2007, 28 (01) : 308 - 312
[39] A study on the influence of cutting parameters on forces during machining the multiphase V-microalloyed steel
V Sivaraman
S Sankaran
L Vijayaraghavan
The International Journal of Advanced Manufacturing Technology, 2015, 79 : 1285 - 1292
[40] A study on the influence of cutting parameters on forces during machining the multiphase V-microalloyed steel
Sivaraman, V.
Sankaran, S.
Vijayaraghavan, L.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2015, 79 (5-8): : 1285 - 1292

← 1 2 3 4 5 →