Influence of polymer functionalization on adhesion, friction and mold fouling

被引：0
|
作者：
Haupt S. [1 ]
Kroger M. [1 ]
Kriiger J. [2 ]
机构：
[1] Technische Universitat Bergakademie Freiberg Institut fur Maschinenelemente, Agricolastrabe 1, Freiberg
[2] Material & Process Development & Industrialization Tires Commercial Tire Technology, Continental Reifen Deutschland GmbH, Jadekamp 30, Hannover
来源：
Tribologie und Schmierungstechnik | 2021年 / 68卷 / 3-4期
关键词：
demolding force; Demolding test rig; mold fouling; polymer; side wall friction;
D O I：
10.24053/TuS-2021-0021
中图分类号：
学科分类号：
摘要：
At the IMKF, eight different elastomer compounds with different polymer compositions were examined for their demolding characteristics and mold fouling. Ten demolding cycles were carried out for each compound and the fouling of the mold was photo-technical recorded after ten demolding cycles. The used polymer composition does not seem to have any significant influence. However, the components of the compound have a significant influence on the friction characteristics while removing of the vulcanizate from the mold. Crosslinking that begins very early has an initiating influence on mold fouling. The measurable fluctuations in the maximum demolding force that occur could correlate with the internal friction of the polymer with the filler. © 2021 Expert Verlag. All rights reserved.
引用
收藏
页码：58 / 66
页数：8
相关论文
共 50 条
  • [31] Suppressing Pseudomonas aeruginosa adhesion via non-fouling polymer brushes
    Rodriguez-Emmenegger, Cesar
    Decker, Antje
    Surman, Frantisek
    Preuss, Corinna M.
    Sedlakova, Zdenka
    Zydziak, Nicolas
    Barner-Kowollik, Christopher
    Schwartz, Thomas
    Barner, Leonie
    RSC ADVANCES, 2014, 4 (110): : 64781 - 64790
  • [32] Mold fouling of EPDM rubber compounds
    Bukhina, M.F.
    Morozov, Yu.L.
    Van, De Ven, P.M.
    Noordermeer, J.W.M.
    Kauchuk i Rezina, 2003, (01): : 12 - 22
  • [33] Mold fouling during rubber vulcanization
    Van, Baarle, Ben
    Rubber World, 2001, 225 (03):
  • [34] Influence of adhesion induced contact areas on sliding friction
    Myshkin, N.
    Kovalev, A.
    Makhovskaya, Yu.
    Torskaya, E.
    Goryacheva, I.
    TRIBOLOGY-MATERIALS SURFACES & INTERFACES, 2010, 4 (03) : 130 - 135
  • [35] Influence of adhesion and friction on the geometry of packings of spherical particles
    Martin, C. L.
    Bordia, R. K.
    PHYSICAL REVIEW E, 2008, 77 (03)
  • [36] The Influence of Elastic Modulus on the Adhesion of Fouling Organism to Poly(dimethylsiloxane) (PDMS)
    Zhang, Jinwei
    Lin, Cunguo
    Wang, Li
    Zheng, Jiyong
    Peng, Yanlei
    Duan, Dongxia
    NEW MATERIALS AND ADVANCED MATERIALS, PTS 1 AND 2, 2011, 152-153 : 1466 - 1470
  • [37] Epoxy mold adhesion on various plasma-treated thermoplastic polymer surfaces
    Gacs, Jeno
    Vernon, Zita
    Kocsis, Laszlo
    Berenyi, Zoltan J.
    Bogya, Erzsebet Sara
    Jacob, Timo
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2022, 120 (7-8): : 4493 - 4504
  • [38] Epoxy mold adhesion on various plasma-treated thermoplastic polymer surfaces
    Jenő Gacs
    Zita Vernon
    László Kocsis
    Zoltán J. Berényi
    Erzsébet Sára Bogya
    Timo Jacob
    The International Journal of Advanced Manufacturing Technology, 2022, 120 : 4493 - 4504
  • [39] Influence of the adhesion force crystal/heat exchanger surface on fouling mitigation
    Förster, M
    Augustin, W
    Bohnet, M
    CHEMICAL ENGINEERING AND PROCESSING-PROCESS INTENSIFICATION, 1999, 38 (4-6) : 449 - 461
  • [40] Influence of the Polymer Surface Layer on the Adhesion of Polymer Matrix Composites
    Benard, Q.
    Fois, M.
    Grisel, M.
    Laurens, P.
    Joubert, F.
    JOURNAL OF THERMOPLASTIC COMPOSITE MATERIALS, 2009, 22 (01) : 51 - 61
12345