Effect of machining area on material removal rate in strip EDM

被引：0
|
作者：
Ki Young Song
Chong Nam Chu
机构：
[1] Sharp Engineering,Department of Mechanical and Aerospace Engineering
[2] Seoul National University,undefined
来源：
International Journal of Precision Engineering and Manufacturing | 2015年 / 16卷
关键词：
Electrical discharge machining; Electrode; Wear;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
Strip EDM is similar to wire EDM, except that the electrode is a roll of brass strip. In this study, investigated is the effect of machining area on material removal rate (MRR) in strip EDM, The MRR was measured according to different machining areas and different electrical discharge conditions. For a given discharge condition, optimal machining area for maximum MRR was identified. The optimal machining area was larger under higher discharge energy condition. It is shown that strip EDM is much more efficient than wire EDM because material removal rate is much higher and the electrode consumption is much less.
引用
收藏
页码：2435 / 2440
页数：5
相关论文
共 50 条
  • [31] Taguchi technique for modeling material removal rate in ultrasonic machining of titanium
    Singh, R.
    Khamba, J. S.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2007, 460 (365-369): : 365 - 369
  • [32] Design of material removal rate to reduce machining time of dental crown
    Sangbeom Nam
    Byungki Kim
    Journal of Mechanical Science and Technology, 2019, 33 : 3423 - 3434
  • [33] A TECHNIQUE AND ITS APPLICATION FOR EVALUATION OF MATERIAL REMOVAL CONTRIBUTIONS OF PULSES IN ELECTRIC-DISCHARGE MACHINING (EDM)
    COGUN, C
    INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 1990, 30 (01): : 19 - 31
  • [34] ON EFFECT OF AMBIENT PRESSURE ON RATE OF REMOVAL IN ULTRASONIC MACHINING
    BARASH, MM
    WATANAPO.D
    INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 1970, 12 (09) : 775 - &
  • [35] Comparative study for material removal rate, surface finish and electrode wear rate on die sinking EDM
    El Grour, H. H.
    Maidin, S.
    PROCEEDINGS OF MECHANICAL ENGINEERING RESEARCH DAY 2015, 2015, : 63 - 64
  • [36] Modeling of Workpiece Removal Rate on EDM
    Han, Fuzhu
    Zhang, Jie
    Cheng, Gang
    Takahito, Inoue
    PROCEEDINGS OF THE 16TH INTERNATIONAL SYMPOSIUM ON ELECTROMACHINING, 2010, 2010, : 101 - 104
  • [37] COMPARATIVE STUDY OF MATERIAL REMOVAL RATE AND TOOL WEAR RATE OF COPPER AND ALUMINIUM ON DIE SINKING EDM
    Maidin, S.
    El Grour, H. H.
    Seeying, C.
    JURNAL TEKNOLOGI, 2015, 77 (21): : 51 - 58
  • [38] Effect of cryogenic treated brass wire electrode on material removal rate in wire electrical discharge machining
    Kapoor, Jatinder
    Singh, Sehijpal
    Khamba, Jaimal Singh
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE, 2012, 226 (C11) : 2750 - 2758
  • [39] Studies on the material removal rate of two-phase eutectic alloys by EDM process
    Tsai, DC
    Song, JM
    Lui, TS
    Chen, LH
    INTERNATIONAL JOURNAL OF CAST METALS RESEARCH, 2002, 15 (01) : 61 - 66
  • [40] Optimization of process parameters of wire EDM for material removal rate using Taguchi technique
    Kumar, Mandeep
    Singh, Hari
    INDIAN JOURNAL OF ENGINEERING AND MATERIALS SCIENCES, 2016, 23 (04) : 223 - 230
12345