Effect of machining area on material removal rate in strip EDM

被引：0
|
作者：
Ki Young Song
Chong Nam Chu
机构：
[1] Sharp Engineering,Department of Mechanical and Aerospace Engineering
[2] Seoul National University,undefined
来源：
International Journal of Precision Engineering and Manufacturing | 2015年 / 16卷
关键词：
Electrical discharge machining; Electrode; Wear;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
Strip EDM is similar to wire EDM, except that the electrode is a roll of brass strip. In this study, investigated is the effect of machining area on material removal rate (MRR) in strip EDM, The MRR was measured according to different machining areas and different electrical discharge conditions. For a given discharge condition, optimal machining area for maximum MRR was identified. The optimal machining area was larger under higher discharge energy condition. It is shown that strip EDM is much more efficient than wire EDM because material removal rate is much higher and the electrode consumption is much less.
引用
收藏
页码：2435 / 2440
页数：5
相关论文
共 50 条
  • [1] Effect of Machining Area on Material Removal Rate in Strip EDM
    Song, Ki Young
    Chu, Chong Nam
    INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING, 2015, 16 (12) : 2435 - 2440
  • [2] Effect of Wire-EDM Machining Parameters on Surface Roughness and Material Removal Rate of High Strength Armor Steel
    Bobbili, Ravindranadh
    Madhu, V.
    Gogia, A. K.
    MATERIALS AND MANUFACTURING PROCESSES, 2013, 28 (04) : 364 - 368
  • [3] Effect of EDM parameters on material removal rate, tool wear rate and geometrical errors of aluminium material
    Selvarajan, L.
    Sasikumar, R.
    Kumar, N. Senthil
    Kolochi, Prabu
    Kumar, P. Naveen
    MATERIALS TODAY-PROCEEDINGS, 2021, 46 : 9392 - 9396
  • [4] Effect of Different Dielectrics on Material Removal Rate, Electrode Wear Rate and Microstructures in EDM
    Niamat, Misbah
    Sarfraz, Shoaib
    Aziz, Haris
    Jahanzaib, Mirza
    Shehab, Essam
    Ahmad, Wasim
    Hussain, Salman
    COMPLEX SYSTEMS ENGINEERING AND DEVELOPMENT, 2017, 60 : 2 - 7
  • [5] Effect of valency on material removal rate in electrochemical machining of aluminium
    Mukherjee, S. K.
    Kumar, S.
    Srivastava, P. K.
    Kumar, Arbind
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2008, 202 (1-3) : 398 - 401
  • [6] EFFECT OF MACHINING AREA AND PULSE PARAMETERS ON EDM PERFORMANCE
    JESWANI, ML
    INDIAN JOURNAL OF TECHNOLOGY, 1980, 18 (09): : 354 - 356
  • [7] Effect of Over Voltage on Material Removal Rate During Electrochemical Machining
    Mukherjee, S. K.
    Kumar, S.
    Srivastava, P. K.
    JOURNAL OF APPLIED SCIENCE AND ENGINEERING, 2005, 8 (01): : 23 - 28
  • [8] Analysis of the influence of input parameters of EDM on material removal rate and surface roughness for machining stainless steel 304
    Ahmed F.
    Ko T.J.
    Ali S.
    International Journal of Machining and Machinability of Materials, 2018, 20 (01): : 78 - 89
  • [9] Optimization of Material Removal Rate and Surface Roughness in EDM Machining of Metal Matrix Composite using Genetic Algorithm
    Aharwal, K. R.
    Sitaram
    Krishna, C. M.
    MATERIALS TODAY-PROCEEDINGS, 2018, 5 (02) : 5391 - 5397
  • [10] Energy Consumption Modeling for EDM Based on Material Removal Rate
    Yang, Mo
    Zhang, Dinghua
    Wu, Baohai
    Zhang, Yunpeng
    IEEE ACCESS, 2020, 8 : 173267 - 173275
12345