Influence of rotational speed during centrifugal casting on sliding wear behaviour of the Al-2Si alloy

被引：5
|
作者：
Mukunda P.G. [1 ]
Shailesh Rao A. [1 ]
Rao S.S. [2 ]
机构：
[1] Department of Mechanical Engineering, Nitte Meenakshi Institute of Technology, Bangalore, Karnataka
[2] Department of Mechanical Engineering, National Institute of Technology Karnataka, Surathkal, Karnataka
来源：
Frontiers of Materials Science in China | 2009年 / 3卷 / 3期
关键词：
Al-Si alloy; Dry sliding wear; Rotational speed;
D O I：
10.1007/s11706-009-0052-x
中图分类号：
学科分类号：
摘要：
The microstructures and dry sliding wear behaviour of an Al-2Si alloy cast centrifugally are studied. Results indicate that at optimum speed the cast has a microstructure consisting of uniformly distributed α-Al grains and fine eutectic silicon grains. The cast exhibited better wear resistance compared to the same cast prepared at different rpms. This paper attempts to investigate the influence of the microstructural changes in the Al-2Si alloy by varying the rotational speed of the mould and its combined action on the dry sliding wear behaviour. © Higher Education Press and Springer-Verlag 2009.
引用
收藏
页码：339 / 344
页数：5
相关论文
共 50 条
  • [11] The impact of centrifugal casting processing parameters on the wear behaviour of Al alloy/Al2O3 functionally graded materials
    Kumar, Bhupendra
    Joshi, Amit
    Mer, K. K. S.
    Prasad, Lalta
    Pathak, Manoj Kumar
    Saxena, Kuldeep K.
    MATERIALS TODAY-PROCEEDINGS, 2022, 62 : 2780 - 2786
  • [12] The impact of centrifugal casting processing parameters on the wear behaviour of Al alloy/Al2O3 functionally graded materials
    Kumar, Bhupendra
    Joshi, Amit
    Mer, K. K. S.
    Prasad, Lalta
    Pathak, Manoj Kumar
    Saxena, Kuldeep K.
    MATERIALS TODAY-PROCEEDINGS, 2022, 62 : 2780 - 2786
  • [13] Sliding Wear Behaviour of In Situ TiB2 Reinforced Hypoeutectic Al-Si Alloy Composites
    M. K. Hullur
    Dayanand M. Goudar
    K. Venkateshwaralu
    S. A. Kori
    International Journal of Metalcasting, 2023, 17 : 1179 - 1190
  • [14] Sliding Wear Behaviour of In Situ TiB2 Reinforced Hypoeutectic Al-Si Alloy Composites
    Hullur, M. K.
    Goudar, Dayanand M.
    Venkateshwaralu, K.
    Kori, S. A.
    INTERNATIONAL JOURNAL OF METALCASTING, 2023, 17 (02) : 1179 - 1190
  • [15] Effect of Rotational Speed in Vertical Centrifugal Casting on the Wear Properties of Obtained Aluminum Tubes
    Tattimani, Mahantesh
    Agari, Shailesh Rao
    IRANIAN JOURNAL OF SCIENCE AND TECHNOLOGY-TRANSACTIONS OF MECHANICAL ENGINEERING, 2019, 43 (03) : 587 - 592
  • [16] Effect of Rotational Speed in Vertical Centrifugal Casting on the Wear Properties of Obtained Aluminum Tubes
    Mahantesh Tattimani
    Shailesh Rao Agari
    Iranian Journal of Science and Technology, Transactions of Mechanical Engineering, 2019, 43 : 587 - 592
  • [17] Dry Sliding Friction and Wear Behaviour of an Electron Beam Melted Hypereutectic Al–Si Alloy
    J. C. Walker
    J. Murray
    S. Narania
    A. T. Clare
    Tribology Letters, 2012, 45 : 49 - 58
  • [18] Transition in dry sliding friction and wear behaviour of cast Al-Si base alloy
    Dwivedi, D.K.
    Journal of the Institution of Engineers (India), Part MM: Metallurgy and Material Science Division, 2001, 82 (02): : 69 - 74
  • [19] Sliding wear and friction behaviour of Al-18% Si-0.5% Mg alloy
    Dwivedi, DK
    Arjun, TS
    Thakur, P
    Vaidya, H
    Singh, K
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2004, 152 (03) : 323 - 328
  • [20] Tribological behaviour of cast hypereutectic Al-Si-Cu alloy subjected to sliding wear
    Lozano, D. E.
    Mercado-Solis, R. D.
    Perez, A. J.
    Talamantes, J.
    Morales, F.
    Hernandez-Rodriguez, M. A. L.
    WEAR, 2009, 267 (1-4) : 545 - 549
12345