Biconical Antenna with Integrated Balun Fabricated in Additive Manufacturing Technology

被引：1

作者：

Gaetano, Domenico ^{[1
]}

Canestri, Christian ^{[1
]}

Calcaterra, Alessandro ^{[1
]}

Bia, Pietro ^{[1
]}

Mitrano, Cosmo ^{[1
]}

机构：

[1] Elettronica SpA, ELT, Design Solut, Rome, Italy

来源：

2020 IEEE INTERNATIONAL SYMPOSIUM ON ANTENNAS AND PROPAGATION AND NORTH AMERICAN RADIO SCIENCE MEETING | 2020年

关键词：

antennas; ultra wideband antennas; omnidirectional antennas; receiving antennas;

D O I：

10.1109/IEEECONF35879.2020.9330017

中图分类号：

TM [电工技术]; TN [电子技术、通信技术];

学科分类号：

0808 ; 0809 ;

摘要：

This paper describes the design and manufacturing of a biconical antenna with integrated balun for ultra-wideband (UWB) applications. The antenna is composed by a Duncan-Minerva balun that feeds a vertically polarized biconical radiating element. The fabrication of the item has been fully realized in Additive Manufacturing (AM) technology to simplify the assembly and reduce the weight. The applied technique has been the Direct Metal Laser Sintering (DMLS). The radiating element works from 200 MHz to 800 MHz ensuring good reflection coefficient and desired omnidirectional patterns. Simulation and measurement results show very close correspondence validating the design.

引用

页码：1617 / 1618

页数：2

共 50 条

[11] Integrated Antenna with Balun Design for Miracast
Lai, Wen-Cheng
2018 7TH IEEE INTERNATIONAL SYMPOSIUM ON NEXT-GENERATION ELECTRONICS (ISNE), 2018, : 52 - 54
[12] Antenna Design Using Modern Additive Manufacturing Technology: A Review
Helena, Diogo
Ramos, Amelia
Varum, Tiago
Matos, Joao Nuno
IEEE ACCESS, 2020, 8 : 177064 - 177083
[13] Wideband Directive Dipole Antenna with Integrated Balun
Kumar, Trivesh
Harish, A. R.
2012 IEEE ANTENNAS AND PROPAGATION SOCIETY INTERNATIONAL SYMPOSIUM (APSURSI), 2012,
[14] A Butler Matrix-Based Multibeam W-Band Slot Antenna Array Fabricated by Metal Additive Manufacturing Technology
Wang, Dongxu
Xu, Kai-Da
Cao, Yuanxi
Guo, Cheng
Yan, Sen
IEEE TRANSACTIONS ON ANTENNAS AND PROPAGATION, 2024, 72 (06) : 5349 - 5354
[15] An Electrically-Small, 3-D Cube Antenna Fabricated with Additive Manufacturing
Nassar, Ibrahim T.
Weller, Thomas M.
2013 IEEE TOPICAL CONFERENCE ON POWER AMPLIFIERS FOR WIRELESS AND RADIO APPLICATIONS (PAWR), 2013, : 91 - 93
[16] An Electrically-Small, 3-D Cube Antenna Fabricated with Additive Manufacturing
Nassar, Ibrahim T.
Weller, Thomas M.
2013 IEEE 13TH TOPICAL MEETING ON SILICON MONOLITHIC INTEGRATED CIRCUITS IN RF SYSTEMS (SIRF), 2013, : 162 - 164
[17] An Electrically-Small, 3-D Cube Antenna Fabricated with Additive Manufacturing
Nassar, Ibrahim T.
Weller, Thomas M.
2013 IEEE TOPICAL CONFERENCE ON BIOMEDICAL WIRELESS TECHNOLOGIES, NETWORKS, AND SENSING SYSTEMS (BIOWIRELESS), 2013, : 85 - 87
[18] An Electrically-Small, 3-D Cube Antenna Fabricated with Additive Manufacturing
Nassar, Ibrahim T.
Weller, Thomas M.
2013 IEEE RADIO AND WIRELESS SYMPOSIUM (RWS), 2013, : 262 - 264
[19] An Electrically-Small, 3-D Cube Antenna Fabricated with Additive Manufacturing
Nassar, Ibrahim T.
Weller, Thomas M.
2013 IEEE TOPICAL CONFERENCE ON WIRELESS SENSORS AND SENSOR NETWORKS (WISNET), 2013, : 58 - 60
[20] Characterization of ceramic components fabricated using binder jetting additive manufacturing technology
Gonzalez, J. A.
Mireles, J.
Lin, Y.
Wicker, R. B.
CERAMICS INTERNATIONAL, 2016, 42 (09) : 10559 - 10564

← 1 2 3 4 5 →