Investigation on fracture toughness of polytetrafluoroethylene with impact essential work of fracture method

被引：2
|
作者：
Armagan, Mustafa [1 ,2 ]
Arici, A. Armagan [2 ]
机构：
[1] Istanbul Medeniyet Univ, Directorate Construct Tech Works, D-100 Hiwy 8, TR-34720 Istanbul, Turkey
[2] Kocaeli Univ, Dept Mech Engn, TR-41001 Izmit, Turkey
来源：
POLYMERS & POLYMER COMPOSITES | 2021年 / 29卷 / 9_SUPPL期
关键词：
Impact essential work of fracture; fracture toughness; polymer; polytetrafluoroethylene; filled-PTFE; Charpy test; scanning electron microscope; GLASS-FIBER; COMPOSITES;
D O I：
10.1177/09673911211003392
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
Polytetrafluoroethylene (PTFE) polymer has a wide range of applications in various industries. Therefore, for designers it is essential to know the strength properties of the material under dynamic loads. In this study, pure-PTFE, bronze and carbon filled-PTFE are tested under dynamic load. In addition, pure and carbon filled specimens were used to determine the temperature effect of PTFE. All tests were carried out in the Charpy impact device according to impact essential work of fracture method. At 23 degrees C, pure-PTFE showed the highest impact strengths, bronze filled-PTFE and carbon filled-PTFE showed lower respectively and it has been found that the carbon filler increases the fracture toughness approximately two times at high temperature (I 50 degrees C). On fracture surfaces phase transitions effects of PTFE and behavior of fillers used were investigated with Scanning Electron Microscope.
引用
收藏
页码：S335 / S343
页数：9
相关论文
共 50 条
  • [31] THE PLANE-STRAIN ESSENTIAL WORK OF FRACTURE AS A MEASURE OF THE FRACTURE-TOUGHNESS OF DUCTILE POLYMERS
    SALEEMI, AS
    NAIRN, JA
    POLYMER ENGINEERING AND SCIENCE, 1990, 30 (04): : 211 - 218
  • [32] Fracture Toughness Characterization of High-Density Polyethylene Using Essential Work of Fracture Concept
    Houari, Tarek
    Benguediab, Mohamed
    Belaziz, Azzeddine
    Belhamiani, Mohamed
    Aid, Abdelkrim
    JOURNAL OF FAILURE ANALYSIS AND PREVENTION, 2020, 20 (01) : 315 - 322
  • [33] Fracture Toughness Characterization of High-Density Polyethylene Using Essential Work of Fracture Concept
    Tarek Houari
    Mohamed Benguediab
    Azzeddine Belaziz
    Mohamed Belhamiani
    Abdelkrim Aid
    Journal of Failure Analysis and Prevention, 2020, 20 : 315 - 322
  • [34] Essential work of fracture compared to fracture mechanics - towards a thickness independent plane stress toughness
    Pardoen, T
    Marchal, Y
    Delannay, F
    ENGINEERING FRACTURE MECHANICS, 2002, 69 (05) : 617 - 631
  • [35] On the impact essential work of fracture of ductile polymers
    Fasce, L
    Bernal, C
    Frontini, P
    Mai, YW
    POLYMER ENGINEERING AND SCIENCE, 2001, 41 (01): : 1 - 14
  • [36] In-plane and Out-of-plane Fracture Toughness of Physically Aged Polyesters as Assessed by the Essential Work of Fracture (EWF) Method
    T. Bárány
    F. Ronkay
    J. Karger-kocsis
    T. Czigány
    International Journal of Fracture, 2005, 135 : 251 - 265
  • [37] In-plane and out-of-plane fracture toughness of physically aged polyesters as assessed by the essential work of fracture (EWF) method
    Bárány, T
    Ronkay, F
    Karger-Kocsis, J
    Czigány, T
    INTERNATIONAL JOURNAL OF FRACTURE, 2005, 135 (1-4) : 251 - 265
  • [38] Fracture Toughness Analysis of Automotive-Grade Dual-Phase Steel Using Essential Work of Fracture (EWF) Method
    Kumar, Sunil M. R.
    Schmidova, Eva
    Konopik, Pavel
    Melzer, Daniel
    Bozkurt, Fatih
    Londe, Neelakantha, V
    METALS, 2020, 10 (08) : 1 - 12
  • [39] Studies on fracture toughness testing of paper by use of thermography part 5 - Calculative correction of the essential work of fracture method for paper
    Tanaka, A
    Matsumoto, T
    Yamauchi, T
    SEN-I GAKKAISHI, 1998, 54 (12) : 685 - 691
  • [40] Examination of the essential work of fracture method for paper
    Tanaka, A
    Yamauchi, T
    TAPPI INTERNATIONAL PAPER PHYSICS CONFERENCE, 1999, : 171 - 177
12345