Experimental Study on the Axis Line Deflection of Ti6A14V Titanium Alloy in Gun-Drilling Process

被引：1

作者：

Li, Liang ^{[1
]}

Xue, Hu ^{[1
]}

Wu, Peng ^{[1
]}

机构：

[1] Yancheng Inst Technol, Yancheng, Peoples R China

来源：

5TH ANNUAL INTERNATIONAL CONFERENCE ON MATERIAL SCIENCE AND ENVIRONMENTAL ENGINEERING (MSEE2017) | 2018年 / 301卷

基金：

中国国家自然科学基金;

关键词：

D O I：

10.1088/1757-899X/301/1/012012

中图分类号：

X [环境科学、安全科学];

学科分类号：

08 ; 0830 ;

摘要：

Titanium alloy is widely used in aerospace industry, but it is also a typical difficult-to-cut material. During Deep hole drilling of the shaft parts of a certain large aircraft, there are problems of bad surface roughness, chip control and axis deviation, so experiments on gun-drilling of Ti6A14V titanium alloy were carried out to measure the axis line deflection, diameter error and surface integrity, and the reasons of these errors were analyzed. Then, the optimized process parameter was obtained during gun-drilling of Ti6A14V titanium alloy with deep hole diameter of 17mm. Finally, we finished the deep hole drilling of 860mm while the comprehensive error is smaller than 0.2mm and the surface roughness is less than 1.6 mu m.

引用

页数：7

共 50 条

[41] Influence of thermal oxidation temperature on the microstructural and tribological behavior of Ti6A14V alloy
Wang, Song
Liao, Zhenhua
Liu, Yuhong
Liu, Weiqiang
SURFACE & COATINGS TECHNOLOGY, 2014, 240 : 470 - 477
[42] A constitutive relation and failure criterion for Ti6A14V alloy at impact rates of strain
Macdougall, DAS
Harding, J
JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS, 1999, 47 (05) : 1157 - 1185
[43] How do titanium and Ti6A14V corrode in fluoridated medium as found in the oral cavity? An in vitro study
Souza, Julio C. M.
Barbosa, Sandra L.
Ariza, Edith A.
Henriques, Mariana
Teughels, Wim
Ponthiaux, Pierre
Celis, Jean-Pierre
Rocha, Luis A.
MATERIALS SCIENCE & ENGINEERING C-MATERIALS FOR BIOLOGICAL APPLICATIONS, 2015, 47 : 384 - 393
[44] Experimental investigation and analysis of drilling in Grade 5 Titanium alloy (Ti-6Al-4V)
Joy, Nivin
Prakash, S.
Krishnamoorthy, A.
Antony, Alphonsa
MATERIALS TODAY-PROCEEDINGS, 2020, 21 : 335 - 339
[45] Modeling and optimization of process parameters in face milling of Ti6A14V alloy using Taguchi and grey relational analysis
Rahman, Al Mazedur
Rob, S. M. Abdur
Srivastava, Anil K.
49TH SME NORTH AMERICAN MANUFACTURING RESEARCH CONFERENCE (NAMRC 49, 2021), 2021, 53 : 204 - 212
[46] Optimisation and tool life study in drilling of titanium (Ti-6Al-4V) alloy
Prabukarthi, A. (prabukarthi.arumugam@gmail.com), 1600, Inderscience Enterprises Ltd., 29, route de Pre-Bois, Case Postale 856, CH-1215 Geneva 15, CH-1215, Switzerland (13): : 2 - 3
[47] A study of mechanical and biological behavior of porous Ti6A14V fabricated on EBM
Petrovic, V.
Blasco, J. R.
Portoles, L.
Morales, I.
Primo, V.
Atienza, C.
Moreno, J. F.
Belloch, V.
INNOVATIVE DEVELOPMENTS ON VIRTUAL AND PHYSICAL PROTOTYPING, 2012, : 115 - 120
[48] Numerical modeling and experimental analysis of thrust cutting force and torque in drilling process of titanium alloy Ti6Al4V
Glaa, Nawel
Mehdi, Kamel
Zitoune, Redouane
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2018, 96 (5-8): : 2815 - 2824
[49] Numerical modeling and experimental analysis of thrust cutting force and torque in drilling process of titanium alloy Ti6Al4V
Mehdi, Kamel (kamel.mehdi@ipeiem.utm.tn), 1600, Springer London (96): : 5 - 8
[50] Numerical modeling and experimental analysis of thrust cutting force and torque in drilling process of titanium alloy Ti6Al4V
Nawel Glaa
Kamel Mehdi
Redouane Zitoune
The International Journal of Advanced Manufacturing Technology, 2018, 96 : 2815 - 2824

← 1 2 3 4 5 →