Experimental Study on the Axis Line Deflection of Ti6A14V Titanium Alloy in Gun-Drilling Process

被引：1

作者：

Li, Liang ^{[1
]}

Xue, Hu ^{[1
]}

Wu, Peng ^{[1
]}

机构：

[1] Yancheng Inst Technol, Yancheng, Peoples R China

来源：

5TH ANNUAL INTERNATIONAL CONFERENCE ON MATERIAL SCIENCE AND ENVIRONMENTAL ENGINEERING (MSEE2017) | 2018年 / 301卷

基金：

中国国家自然科学基金;

关键词：

D O I：

10.1088/1757-899X/301/1/012012

中图分类号：

X [环境科学、安全科学];

学科分类号：

08 ; 0830 ;

摘要：

Titanium alloy is widely used in aerospace industry, but it is also a typical difficult-to-cut material. During Deep hole drilling of the shaft parts of a certain large aircraft, there are problems of bad surface roughness, chip control and axis deviation, so experiments on gun-drilling of Ti6A14V titanium alloy were carried out to measure the axis line deflection, diameter error and surface integrity, and the reasons of these errors were analyzed. Then, the optimized process parameter was obtained during gun-drilling of Ti6A14V titanium alloy with deep hole diameter of 17mm. Finally, we finished the deep hole drilling of 860mm while the comprehensive error is smaller than 0.2mm and the surface roughness is less than 1.6 mu m.

引用

页数：7

共 50 条

[31] INFLUENCE OF PROCESS PARAMETERS IN FRICTION DRILLING OF TITANIUM TI-6AL-4V ALLOY
Pangjundee, Thongchai
Muttamara, Apiwat
MM SCIENCE JOURNAL, 2021, 2021 : 4791 - 4796
[32] Analysis of material behavior models for the Ti6A14V alloy to simulate the Single Point Incremental Forming process
Naranjo, J.
Miguel, V.
Martinez, A.
Coello, J.
Manjabacas, M. C.
MANUFACTURING ENGINEERING SOCIETY INTERNATIONAL CONFERENCE 2017 (MESIC 2017), 2017, 13 : 307 - 314
[33] Structural characterization of titanium oxide layers prepared by plasma based ion implantation with oxygen on Ti6A14V alloy
Li, Jinlong
Sun, Mingren
Ma, Xinxin
APPLIED SURFACE SCIENCE, 2006, 252 (20) : 7503 - 7508
[34] FRICTION AND WEAR BEHAVIORS OF Ti6A14V ALLOY TREATED BY PLASMA Ni ALLOYING
Wang, Zhenxia
Cai, Wenlan
Wu, Hairui
Lin, Naiming
Yao, Xiaohong
He, Zhiyong
Liu, Xiaoping
SURFACE REVIEW AND LETTERS, 2018, 25 (05)
[35] MODELING OF DYNAMIC RECRYSTALLIZATION OF Ti6A14V ALLOY USING A CELLULAR AUTOMATON APPROACH
J.W.Zhao~(1)*) H.Din~(1)) W.J.Zhao~(1)) F.R.Cao~(1)) H.L.Hou~(2)) Z.Q.Li~(2)) 1)School of Materials and Metallurgy
Acta Metallurgica Sinica(English Letters), 2008, (04) : 260 - 268
[36] Bacteria adherence property of molybdenum nitride modified layer on Ti6A14V alloy
Fan Ai-lan
Tian Lin-hai
Qin Lin
Tang Bin
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, 2007, 17 : S889 - S891
[37] Drilling of titanium alloy (Ti6Al4V) - a review
Yuan, Chua Guang
Pramanik, A.
Basak, A. K.
Prakash, C.
Shankar, S.
MACHINING SCIENCE AND TECHNOLOGY, 2021, 25 (04) : 637 - 702
[38] Nanoindentation Measurement of Creep Stress Exponent of Ti6A14V Alloy at Room Temperature
Meng Longhui
Yang Yinfei
He Ning
RARE METAL MATERIALS AND ENGINEERING, 2016, 45 (03) : 617 - 622
[39] Corrosion-wear behavior of molybdenum nitride layer on Ti6A14V alloy
Qin Lin
Zhan Ke
Fan Ailan
Tang Bin
RARE METAL MATERIALS AND ENGINEERING, 2008, 37 (04) : 725 - 728
[40] Effect of laser peening on friction and wear behavior of medical Ti6A14V alloy
Zhou, Jianzhong
Sun, Yunjie
Huang, Shu
Sheng, Jie
Li, Jing
Agyenim-Boateng, Emmanuel
OPTICS AND LASER TECHNOLOGY, 2019, 109 : 263 - 269

← 1 2 3 4 5 →