Creep deformation of TiAl-Si alloys with aligned γ/α2 lamellar microstructures

被引：30
|
作者：
Johnson, DR [1 ]
Masuda, Y
Yamanaka, T
Inui, H
Yamaguchi, M
机构：
[1] Purdue Univ, Sch Mat Engn, W Lafayette, IN 47907 USA
[2] Kyoto Univ, Dept Mat Sci & Engn, Kyoto 6068501, Japan
来源：
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE | 2000年 / 31卷 / 10期
关键词：
D O I：
10.1007/s11661-000-0192-1
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Creep tests were conducted on directionally solidified TiAl-Si alloys to discern the effect of lamellar spacing and lamellar orientation on the high-temperature strength. Directional solidification of a Ti-43Al-3Si alloy was used to produce a model microstructure consisting of a single gamma/alpha(2) lamellar colony of controlled orientation for creep testing. Different heat treatments were used to vary the lamellar spacing and tensile creep tests were performed at 750 degrees C using applied stresses of 180, 210, and 240 MPa. In addition, ingots with large columnar grains of various lamellar orientation were also tested. The results clearly show the beneficial effect of microstructural control with the aligned microstructure having a much superior creep resistance. Furthermore, for specimens with aligned lamellar microstructure, decreasing the lamellar spacing greatly improved creep resistance, as both the primary creep strain and secondary creep rate are much smaller for materials with the fine lamellar spacing.
引用
收藏
页码：2463 / 2473
页数：11
相关论文
共 50 条
  • [1] Creep deformation of TiAl-Si alloys with aligned γ/α2 lamellar microstructures
    D. R. Johnson
    Y. Masuda
    T. Yamanaka
    H. Inui
    M. Yamaguchi
    [J]. Metallurgical and Materials Transactions A, 2000, 31 : 2463 - 2473
  • [2] Creep of TiAl-Si alloys with aligned lamellar microstrucures
    Johnson, DR
    Masuda, Y
    Yamanaka, T
    Inui, H
    Yamaguchi, M
    [J]. GAMMA TITANIUM ALUMINIDES 1999, 1999, : 627 - 631
  • [3] Directional solidification and creep deformation of TiAl-Si alloys
    Yamanaka, T
    Johnson, DR
    Masuda, Y
    Inui, H
    Yamaguchi, M
    [J]. GAMMA TITANIUM ALUMINIDES 1999, 1999, : 295 - 300
  • [4] Creep deformation of directionally-solidified TiAl-based alloys with aligned lamellar microstructures
    Omiya, Y
    Muto, S
    Yamanaka, T
    Johnson, DR
    Inui, H
    Yamaguchi, M
    [J]. PRICM 4: FORTH PACIFIC RIM INTERNATIONAL CONFERENCE ON ADVANCED MATERIALS AND PROCESSING, VOLS I AND II, 2001, : 915 - 918
  • [5] Directional solidification of TiAl-Re-Si alloys with aligned γ/α2 lamellar microstructures
    Yamanaka, T
    Johnson, DR
    Inui, H
    Yamaguchi, M
    [J]. INTERMETALLICS, 1999, 7 (07) : 779 - 784
  • [6] Creep deformation in gamma TiAl alloys with lamellar structures
    Nieh, TG
    Wang, JN
    Hsiung, LM
    [J]. THERMEC '97 - INTERNATIONAL CONFERENCE ON THERMOMECHANICAL PROCESSING OF STEELS AND OTHER MATERIALS, VOLS I-II, 1997, : 1423 - 1431
  • [7] Crystal Plasticity Modeling of Creep in Alloys with Lamellar Microstructures at the Example of Fully Lamellar TiAl
    Schnabel, Jan E.
    Scheider, Ingo
    [J]. FRONTIERS IN MATERIALS, 2021, 7
  • [8] .1. Creep deformation of duplex and lamellar TiAl alloys
    Morris, MA
    Lipe, T
    [J]. INTERMETALLICS, 1997, 5 (05) : 329 - 337
  • [9] Directional solidification and microstructural control of the TiAl/Ti3Al lamellar microstructure in TiAl-Si alloys
    Johnson, DR
    Inui, H
    Yamaguchi, M
    [J]. ACTA MATERIALIA, 1996, 44 (06) : 2523 - 2535
  • [10] Development of TiAl-Si Alloys-A Review
    Knaislova, Anna
    Novak, Pavel
    Cabibbo, Marcello
    Jaworska, Lucyna
    Vojtech, Dalibor
    [J]. MATERIALS, 2021, 14 (04) : 1 - 22
12345