Optimization of friction coefficient of kenaf/epoxy composites as an alternative friction material using Taguchi method

被引：0
|
作者：
Mustafa, A. [1 ]
Abdollah, M. F. B. [1 ,2 ]
Amiruddin, H. [1 ,2 ]
Shuhimi, F. F. [1 ]
Tahir, N. A. M. [1 ]
Muhammad, N. [1 ,2 ]
Kamal, S. E. Mat [1 ,2 ]
Ismail, N. [1 ,2 ,3 ]
机构：
[1] Univ Teknikal Malaysia Melaka, Fac Mech Engn, Durian Tunggal 76100, Melaka, Malaysia
[2] Univ Teknikal Malaysia Melaka, Ctr Adv Res Energy, Durian Tunggal 76100, Melaka, Malaysia
[3] Univ Twente, Fac Engn Technol, Dept Surface Technol & Tribol, POB 217, NL-7500 AE Enschede, Netherlands
来源：
PROCEEDINGS OF MECHANICAL ENGINEERING RESEARCH DAY 2016 | 2016年
关键词：
Kenaf; polymer composite; friction coefficient;
D O I：
暂无
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
This paper introduces the application of Taguchi optimization methodology in optimizing the design factors for obtaining high friction coefficient of kenaf/epoxy composites under dry sliding condition. An orthogonal array of the Taguchi method was set-up and used to analyse the effect of the design parameters on the friction coefficient. Tribological testing was conducted using a pin-on-disc tribometer. For the highest friction coefficient, 45wt.% non-treated kenaf fiber sliding at 19.62N, 500rpm and 100 degrees C is found to be the optimized combination of levels of all the six control factors. The confirmation test proves that the optimized friction coefficient is within the range of friction coefficient of conventional friction material.
引用
收藏
页码：11 / 12
页数：2
相关论文
共 50 条
  • [21] Friction Wear of Modified Epoxy Composites
    P. P. Savchuk
    A. G. Kostornov
    V. P. Kashitskii
    O. L. Sadova
    Powder Metallurgy and Metal Ceramics, 2014, 53 : 205 - 209
  • [22] Welding Parameter Optimization of Alloy Material by Friction Stir Welding Using Taguchi Approach and Design of Experiments
    Karwande, Amit H.
    Rao, Seeram Srinivasa
    INTERNATIONAL CONFERENCE ON ELECTRICAL, ELECTRONICS, MATERIALS AND APPLIED SCIENCE, 2018, 1952
  • [23] Optimization of process parameters on engine exhaust valves using Taguchi method in friction welding process
    Nagasankar, P.
    Gurusamy, P.
    Gopinath, S.
    Gnanaprakash, K.
    Pradeep, G.
    MATERIALS TODAY-PROCEEDINGS, 2020, 33 : 3212 - 3217
  • [24] Optimization of microstructural and mechanical properties of friction stir welding using the cellular automaton and Taguchi method
    Shojaeefard, Mohammad Hasan
    Akbari, Mostafa
    Khalkhali, Abolfazl
    Asadi, Parviz
    Parivar, Amir Hossein
    MATERIALS & DESIGN, 2014, 64 : 660 - 666
  • [25] Friction stir welding of AL–MG alloy optimization of process parameters using Taguchi method
    S. Vijayan
    R. Raju
    K. Subbaiah
    N. Sridhar
    S. R. K. Rao
    Experimental Techniques, 2010, 34 : 37 - 44
  • [26] Static Friction Coefficient Is Not a Material Constant
    Ben-David, Oded
    Fineberg, Jay
    PHYSICAL REVIEW LETTERS, 2011, 106 (25)
  • [27] Optimization of process parameters for friction stir lap welding of carbon fibre reinforced thermoplastic composites by Taguchi method
    Ahmadi, H.
    Arab, N. B. Mostafa
    Ghasemi, F. Ashenai
    JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY, 2014, 28 (01) : 279 - 284
  • [28] Optimization of process parameters for friction stir lap welding of carbon fibre reinforced thermoplastic composites by Taguchi method
    H. Ahmadi
    N. B. Mostafa Arab
    F. Ashenai Ghasemi
    Journal of Mechanical Science and Technology, 2014, 28 : 279 - 284
  • [29] Optimization of method a load cell calibration for the measurement of coefficient of friction
    Castro, R. M.
    Pereira, M.
    Sousa, A. R.
    Curi, E. I. M.
    Izidoro, C. L.
    Correa, L. C.
    8TH BRAZILIAN CONGRESS ON METROLOGY (METROLOGIA 2015), 2016, 733
  • [30] Impact and Ballistic Behavior Optimization of Kevlar–Epoxy Composites by Taguchi Method
    H. Omidvar
    K. K. Azari
    A. Mohammad Taheri
    A. A. Saghafi
    Arabian Journal for Science and Engineering, 2013, 38 : 1161 - 1167
12345