High-energy ball milling of Cu-5mass%C powders

被引：0

作者：

Jin, YP ^{[1
]}

Guo, B ^{[1
]}

Wang, ED ^{[1
]}

机构：

[1] Harbin Inst Technol, Sch Mat Sci & Engn, Harbin 150001, Peoples R China

来源：

PROCEEDINGS OF THE 1ST INTERNATIONAL CONFERENCE ON NEW FORMING TECHNOLOGY | 2004年

关键词：

ball milling; Cu-5mass%C composite powders; grain refinement; distortion of lattice;

D O I：

暂无

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Cu-5mass%C composite powders were prepared by high-energy ball milling. Their microstructures and effects of ball milling time on their microstructure were investigated. The result shows that distortion of lattice, grain refinement and broadened diffraction peak of Cu were seen after high-energy ball milling. Within the initial 2 hours of ball milling, grain of Cu in Cu-5mass%C composite powders was refined suddenly, then slowly. Grain size of Cu was about 20nm by ball milling for 5h. Diffraction peak of graphite disappeared after 2-hour-milling. High-energy ball milling extended solid solubility of C in Cu. Microstrain of Cu in Cu-5mass%C composite powders didn't increase with milling time. After ball milling for 3h, microstrain reached the maximum value. Over 15h-ball milling hardly affected microstrain of Cu in Cu-5mass%C composite powders.

引用

页码：639 / 643

页数：5

共 50 条

[21] Green Synthesis of Ceramic Powders for Tribological Applications Using High-energy Ball Milling
Sikora, Teodora
Kozlowski, Mark T.
Dulian, Piotr
Moszumanski, Ryszard
Wieczorek-Ciurowa, Krystyna
[J]. ICHEAP-11: 11TH INTERNATIONAL CONFERENCE ON CHEMICAL AND PROCESS ENGINEERING, PTS 1-4, 2013, 32 : 2095 - 2100
[22] Nanostructured FeNiZrB powders synthesized by high-energy ball milling: structural and hyperfine characterizations
Pena Rodriguez, V. A.
Medina Medina, J.
Rojas-Ayala, C.
Paucar Cabrera, P.
Landauro, C., V
Quispe-Marcatoma, J.
Rojas Tapia, J.
Baggio-Saitovitch, E. M.
Passamani, E. C.
[J]. HYPERFINE INTERACTIONS, 2021, 242 (01):
[23] Preparation of PUT powders from oxides via high-energy ball milling process
Peng, QS
Jiang, W
Li, JF
[J]. HIGH-PERFORMANCE CERAMICS III, PTS 1 AND 2, 2005, 280-283 : 623 - 625
[24] Fabrication of silicon carbide reinforced aluminium powders by high-energy ball-milling
Wielage, B.
Nestler, D.
Siebeck, S.
Podlesak, H.
[J]. MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK, 2010, 41 (06) : 476 - 481
[25] Effect of high-energy ball milling on the Mg alloy powders under alcohol protection
Li, Gang
Liu, Xingxing
Guo, Qi
Tang, Jianren
Yan, Biao
[J]. PROGRESS IN POWDER METALLURGY, PTS 1 AND 2, 2007, 534-536 : 785 - +
[26] Electrochemical Kinetic Analysis of Carbon Steel Powders Produced by High-Energy Ball Milling
Soliz, Alvaro
Guzman, Danny
Caceres, Luis
Madrid, Felipe M. Galleguillos
[J]. METALS, 2022, 12 (04)
[27] Characterization of titanium powders processed in n-hexane by high-energy ball milling
A. H. Restrepo
J. M. Ríos
F. Arango
E. Correa
A. A. Zuleta
A. Valencia-Escobar
F. J. Bolivar
J. G Castaño
F. E. Echeverría
[J]. The International Journal of Advanced Manufacturing Technology, 2020, 110 : 1681 - 1690
[28] Characterization of titanium powders processed in n-hexane by high-energy ball milling
Restrepo, A. H.
Rios, J. M.
Arango, F.
Correa, E.
Zuleta, A. A.
Valencia-Escobar, A.
Bolivar, F. J.
Castano, J. G.
Echeverria, F. E.
[J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2020, 110 (7-8): : 1681 - 1690
[29] Nanostructured FeNiZrB powders synthesized by high-energy ball milling: structural and hyperfine characterizations
V. A. Peña Rodríguez
J. Medina Medina
C. Rojas-Ayala
P. Paucar Cabrera
C. V. Landauro
J. Quispe-Marcatoma
J. Rojas Tapia
E. M. Baggio-Saitovitch
E. C. Passamani
[J]. Hyperfine Interactions, 2021, 242
[30] A simple route to produce tungsten carbide powders by high-energy ball milling and annealing
Fernique, R. M. T.
Savoie, S.
Gariepy, M.
Braidy, N.
Schulz, R.
[J]. CERAMICS INTERNATIONAL, 2020, 46 (02) : 1736 - 1742

← 1 2 3 4 5 →