Design and verify a natural frequency using ANSYS software

被引：2
|
作者：
Kukreja, Nitin [1 ]
Singhal, Piyush [1 ]
机构：
[1] GLA Univ, Dept Mech Engn, Mathura, India
来源：
MATERIALS TODAY-PROCEEDINGS | 2021年 / 45卷
关键词：
Milling spindle; ANSYS; Finite element analysis; FFT analyzer;
D O I：
10.1016/j.matpr.2020.12.386
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
In this paper we determine the natural frequency of highest speed milling spindle for length 335.4 mm and 16000 rpm speed based on modal analysis. This manuscript taking the high speed milling spindle of bar that is derived and presented by using finite element model in ANSYS software. This method takes into account bearing support contact interface that is recognized by spring damper element COMBIN 14 for giving cushioning effect to spindle. Furthermore, the modal analysis has completed by means of ANSYS commercial software. After that this result is compared with experimental result provided by FFT analyzer. The results show that the natural resonance region speed is far greater than the designed milling spindle. (c) 2021 Elsevier Ltd. All rights reserved. Selection and peer-review under responsibility of the scientific committee of the International Conference on Advances in Materials Research-2019.
引用
收藏
页码：3255 / 3258
页数：4
相关论文
共 50 条
  • [31] A Framework to Formally Verify Conformance of a Software Process to a Software Method
    Khelladi, Djamel-Eddine
    Bendraou, Reda
    Baarir, Souheib
    Laurent, Yoann
    Gervais, Marie-Pierre
    30TH ANNUAL ACM SYMPOSIUM ON APPLIED COMPUTING, VOLS I AND II, 2015, : 1518 - 1525
  • [32] Methodology of teaching methods of FEM analysis using software ANSYS
    Kralik, Juraj
    Kralik, Juraj Jr Jr
    INTERNATIONAL JOURNAL OF EDUCATION AND INFORMATION TECHNOLOGIES, 2022, 16 : 12 - 28
  • [33] CRACK IDENTIFICATION IN REINFORCED CONCRETE BEAMS USING ANSYS SOFTWARE
    Dahmani, L.
    Khennane, A.
    Kaci, S.
    STRENGTH OF MATERIALS, 2010, 42 (02) : 232 - 240
  • [34] Simulation of an active indirect hybrid dehydrator using ANSYS software
    Cabrera, Jose
    Jurado, Francisco
    Vera, David
    ENFOQUE UTE, 2021, 12 (04): : 29 - 44
  • [35] Crack identification in reinforced concrete beams using ANSYS software
    L. Dahmani
    A. Khennane
    S. Kaci
    Strength of Materials, 2010, 42 : 232 - 240
  • [36] Optimization of Remote Economizer Flue Duct Using the ANSYS Software
    Roslyakov, P. V.
    Khokhlov, D. A.
    Egorova, L. E.
    Zaichenko, M. N.
    Grisha, B. G.
    2018 IV INTERNATIONAL CONFERENCE ON INFORMATION TECHNOLOGIES IN ENGINEERING EDUCATION (INFORINO), 2018,
  • [37] Modal analysis of cracked cantilever beam using ANSYS software
    Ahiwale D.
    Madake H.
    Phadtare N.
    Jarande A.
    Jambhale D.
    Materials Today: Proceedings, 2022, 56 : 165 - 170
  • [38] Investigation of the Edge Effect in Laminated Composites Using the ANSYS Software
    Skvortsov Yu.V.
    Evtushenko M.A.
    Khnyryova E.S.
    Journal of Aeronautics, Astronautics and Aviation, 2022, 54 (04): : 421 - 432
  • [39] Design and development of 48V PMBLDC motor for radiator fan application by using ANSYS Maxwell software
    Pawar, Atul J.
    Patil, Anupama
    2017 IEEE 3RD INTERNATIONAL CONFERENCE ON SENSING, SIGNAL PROCESSING AND SECURITY (ICSSS), 2017, : 247 - 252
  • [40] Proving it works:: Using PROC COMPARE to verify an analysis converted into SAS® software
    Haworth, L
    Karanja, N
    PROCEEDINGS OF THE TWENTY-THIRD ANNUAL SAS USERS GROUP INTERNATIONAL CONFERENCE, 1998, : 1080 - 1085
12345