Spray Cooling Heat Transfer and Calculation of Water Impact Density for Cooling of Steel Sheet Materials by Inverse Process Modelling

被引：8

作者：

Wendelstorf, J. ^{[1
]}

Wendelstorf, R. ^{[1
]}

Spitzer, K. -H. ^{[1
]}

机构：

[1] Tech Univ Clausthal, Inst Met, D-38678 Clausthal Zellerfeld, Germany

来源：

STEEL RESEARCH INTERNATIONAL | 2009年 / 80卷 / 09期

关键词：

water cooling; process model; heat transfer coefficient; run-out table; steel strip; PLATE; TEMPERATURES; STRIP;

D O I：

10.2374/SRI09SP054

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

Modern steel grades require accurate temperature control during processing. The cooling section technology has to deliver prescribed cooling rates while fulfilling specific constraints, e.g. on the minimum surface temperature. For all material thicknesses, numerical cooling system set value prediction is advantageous and above 10 mm, the possible cooling rates and the experimental parameter determination are limited by physical constraints. Laboratory measurements provide quantitative experimental data on the heat transfer coefficient (HTC) depending on the cooling system parameter water impact density and the temperature difference. The desired final material properties determine temperature control and cooling rate. This information is used to predict the optimum cooling section set values for a specific cooling task. The inverse modelling calculations use a simple cooling section process model. Illustrative examples for optimum cooling of strip or sheet material using water spray cooling demonstrate the approach. Additionally, the physical limitations due to the finite heat conductivity of the strip are calculated and discussed.

引用

页码：639 / 644

页数：6

共 50 条

[21] Study on transient heat transfer process of spray cooling with closed-loop
Zhou N.
Xu M.
Feng H.
Duan F.
Wang Q.
Chen H.
Guo Q.
Zhou, Nianyong (zhounianyong@cczu.edu.cn), 2020, Materials China (71): : 1018 - 1025
[22] Estimating surface heat flux of spray cooling by inverse heat-transfer computation and sparse regression
Li, Min
Wu, Youjian
Wen, Zhexi
INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER, 2024, 152
[23] Heat transfer in the film boiling regime: Single drop impact and spray cooling
Breitenbach, Jan
Roisman, Ilia V.
Tropea, Cameron
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2017, 110 : 34 - 42
[24] Spray water cooling heat transfer under oxide scale formation conditions
Viscorova, R.
Scholz, R.
Spitzer, K. -H.
Wendelstorf, J.
ADVANCED COMPUTATIONAL METHODS IN HEAT TRANSFER IX, 2006, 53 : 163 - +
[25] Experimental Study on Impact of Installation Angle on Heat Transfer Performance of Spray Cooling
Pang Liping
Liu Zhixuan
Jin Shicheng
Ji Yibin
Zhang Yu
PROCEEDINGS OF THE INTERNATIONAL CONFERENCE ON LOGISTICS, ENGINEERING, MANAGEMENT AND COMPUTER SCIENCE, 2014, 101 : 250 - 253
[26] Computer modeling of liquid droplet impact on heat transfer during spray cooling
Selvam, R. Panneer
Bhaskara, Sandya
Balda, Juan C.
Barlow, Fred
Elshabini, Aicha.
HT2005: Proceedings of the ASME Summer Heat Transfer Conference 2005, Vol 2, 2005, : 179 - 188
[27] Modelling of air-mist spray cooling heat transfer for continuous slab casting
Ramstorfer, F.
Roland, J.
Chimani, C.
Moerwald, K.
INTERNATIONAL JOURNAL OF CAST METALS RESEARCH, 2009, 22 (1-4) : 39 - 42
[28] Spray water cooling heat transfer at high temperatures and liquid mass fluxes
Wendelstorf, J.
Spitzer, K. -H.
Wendelstorf, R.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2008, 51 (19-20) : 4902 - 4910
[29] FOULING OF HEAT-EXCHANGERS FROM COOLING WATER AND PROCESS MATERIALS
CAPPER, CB
EFFLUENT & WATER TREATMENT JOURNAL, 1974, 14 (06): : 309 - 314
[30] Characterisation of the spray cooling heat transfer involved in a high pressure die casting process
Liu, GW
Morsi, YS
Clayton, BR
INTERNATIONAL JOURNAL OF THERMAL SCIENCES, 2000, 39 (05) : 582 - 591

← 1 2 3 4 5 →