Spray Cooling Heat Transfer and Calculation of Water Impact Density for Cooling of Steel Sheet Materials by Inverse Process Modelling

被引：8

作者：

Wendelstorf, J. ^{[1
]}

Wendelstorf, R. ^{[1
]}

Spitzer, K. -H. ^{[1
]}

机构：

[1] Tech Univ Clausthal, Inst Met, D-38678 Clausthal Zellerfeld, Germany

来源：

STEEL RESEARCH INTERNATIONAL | 2009年 / 80卷 / 09期

关键词：

water cooling; process model; heat transfer coefficient; run-out table; steel strip; PLATE; TEMPERATURES; STRIP;

D O I：

10.2374/SRI09SP054

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

Modern steel grades require accurate temperature control during processing. The cooling section technology has to deliver prescribed cooling rates while fulfilling specific constraints, e.g. on the minimum surface temperature. For all material thicknesses, numerical cooling system set value prediction is advantageous and above 10 mm, the possible cooling rates and the experimental parameter determination are limited by physical constraints. Laboratory measurements provide quantitative experimental data on the heat transfer coefficient (HTC) depending on the cooling system parameter water impact density and the temperature difference. The desired final material properties determine temperature control and cooling rate. This information is used to predict the optimum cooling section set values for a specific cooling task. The inverse modelling calculations use a simple cooling section process model. Illustrative examples for optimum cooling of strip or sheet material using water spray cooling demonstrate the approach. Additionally, the physical limitations due to the finite heat conductivity of the strip are calculated and discussed.

引用

页码：639 / 644

页数：6

共 50 条

[11] Heat transfer process of R600a spray cooling system
Xu, Hongbo
Qian, Chunchao
Shao, Shuangquan
Tian, Changqing
Si, Chunqiang
Qiangjiguang Yu Lizishu/High Power Laser and Particle Beams, 2015, 27 (07):
[12] Research on the heat transfer characteristics of air-atomized water spray cooling by experiment and inverse heat conduction method
Ning, Lidan
Luo, Shuncun
Li, Zhichao
He, Lianfang
Li, Huiping
HEAT AND MASS TRANSFER, 2022, 58 (07) : 1247 - 1262
[13] Research on the heat transfer characteristics of air-atomized water spray cooling by experiment and inverse heat conduction method
Lidan Ning
Shuncun Luo
Zhichao Li
Lianfang He
Huiping Li
Heat and Mass Transfer, 2022, 58 : 1247 - 1262
[14] Heat Transfer Modeling of an Annular On-Line Spray Water Cooling Process for Electric-Resistance-Welded Steel Pipe
Chen, Zejun
Han, Huiquan
Ren, Wei
Huang, Guangjie
PLOS ONE, 2015, 10 (07):
[15] Experimental investigation on heat transfer of spray cooling with the mixture of ethanol and water
Liu, Hong
Cai, Chang
Yin, Hongchao
Luo, Jia
Jia, Ming
Gao, Jiuliang
INTERNATIONAL JOURNAL OF THERMAL SCIENCES, 2018, 133 : 62 - 68
[16] Heat Transfer Enhancement of Water Spray Cooling by the Surface Roughness Effect
Lee, Jungho
TRANSACTIONS OF THE KOREAN SOCIETY OF MECHANICAL ENGINEERS B, 2010, 34 (02) : 203 - 212
[17] SIMULATION OF HEAT TRANSFER BY WATER SPRAY COOLING DURING THE CONTINUOUS CASTING OF LOW CARBON STEEL.
Zhang Keqiang
Yuan Weixia
Jinshu Xuebao/Acta Metallurgica Sinica, 1985, 21 (06):
[18] Heat Transfer During Cooling of Steel Surfaces by Water.
Diener, A.
Hammel, W.
Drastik, A.
ESTEL, Berichte aus Forschung und Entwicklung Unserer Werke, 1975, 10 (02): : 78 - 86
[19] Heat transfer coefficient of cooling water in continuous casting by inverse method
Shi, Hongjun
Yang, Yitao
Zhang, Henghua
Shao, Guangjie
Tezhong Zhuzao Ji Youse Hejin/Special Casting and Nonferrous Alloys, 2005, 25 (09): : 528 - 530
[20] Heat transfer regimes and critical heat flux during spray cooling with subcooled water
Vladyko, I. V.
Surtaev, A. S.
Miskiv, N. B.
Mikhailov, A. V.
Nazarov, A. D.
Pavlenko, A. N.
THERMOPHYSICS AND AEROMECHANICS, 2024, 31 (04) : 749 - 753

← 1 2 3 4 5 →