In-pile testing of ITER first wall mock-ups at relevant thermal loading conditions

被引：4

作者：

Litunovsky, N. ^{[1
]}

Gervash, A. ^{[1
]}

Lorenzetto, P. ^{[2
]}

Mazul, I. ^{[1
]}

Melder, R. ^{[3
]}

机构：

[1] DV Efremov Sci Res Inst Electrophys Apparatus, St Petersburg, Russia

[2] EFDA, Barcelona, Spain

[3] Res Inst Atom Reactors, Dimitrovgrad, Russia

来源：

JOURNAL OF NUCLEAR MATERIALS | 2009年 / 386-88卷

关键词：

D O I：

10.1016/j.jnucmat.2008.12.268

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

The paper describes the experimental technique and preliminary results of thermal fatigue testing of ITER first wall (FW) water-cooled mock-ups inside the core of the RBT-6 experimental fission reactor (RIAR, Dimitrovgrad, Russia). This experiment has provided simultaneous effect of neutron fluence and thermal cycling damages on the mock-ups. A PC-controlled high-temperature graphite ohmic heater was applied to provide cyclic thermal load onto the mock-ups surface. This experiment lasted for 309 effective irradiation days with a final damage level (CuCrZr) of 1 dpa in the mock-ups. About 3700 thermal cycles with a heat flux of 0.4-0.5 MW/m(2) onto the mock-ups were realized before the heater fails. Then, irradiation was continued in a non-cycling mode. (C) 2009 Elsevier B.V. All rights reserved.

引用

页码：979 / 982

页数：4

共 50 条

[31] Manufacturing and testing of large-scale mock-ups of ITER plasma facing components in Russia
Belyakov, V
Mazul, I
Strebkov, Y
FUSION ENGINEERING AND DESIGN, 2002, 61-62 : 129 - 134
[32] Ultimate tensile strength testing campaign on ITER pre-compression ring mock-ups
Rossi, Paolo
Capobianchi, Mario
Crescenzi, Fabio
Massimi, Alberto
Mugnaini, Giampiero
Nardi, Claudio
Pizzuto, Aldo
Bettinali, Livio
Knaster, Juan
Rajainmaki, Hannu
Evans, David
FUSION ENGINEERING AND DESIGN, 2011, 86 (6-8) : 1519 - 1522
[33] HIGH HEAT FLUX TEST WITH HIP BONDED 50X50 BE/CU MOCK-UPS FOR THE ITER FIRST WALL
Lee, Dong Won
Bae, Young Dug
Kim, Suk Kwon
Hong, Bong Guen
Jung, Hyun Kyu
Park, Jeong Yong
Jeong, Yong Hwan
Choi, Byung Kwon
FUSION SCIENCE AND TECHNOLOGY, 2009, 56 (01) : 48 - 51
[34] Comparison between FEM and high heat flux thermal fatigue testing results of ITER divertor plasma facing mock-ups
Crescenzi, F.
Roccella, S.
Visca, E.
Moriani, A.
FUSION ENGINEERING AND DESIGN, 2014, 89 (7-8) : 985 - 990
[35] Thermal fatigue testing of actively cooled divertor mock-ups after neutron irradiation
Roedig, M
Duwe, R
Linke, J
Pott, G
Wiechers, B
FUSION TECHNOLOGY, 1998, 34 (03): : 464 - 468
[36] Thermal fatigue testing of actively cooled divertor mock-ups after neutron irradiation
Roedig, Manfred
Duwe, Reiner
Linke, Jochen
Port, Guenther
Wiechers, Bernhard
Fusion Technology, 1998, 34 (3 pt 2): : 464 - 468
[37] Strain life analysis of the first wall mock up under ITER-relevant heat flux conditions
Du, J.
Loewenhoff, Th
Pintsuk, G.
Linke, J.
Wirtz, M.
FUSION ENGINEERING AND DESIGN, 2020, 161 (161)
[38] Manufacturing, testing and post-test examination of ITER divertor vertical target W small scale mock-ups
Visca, Eliseo
Cacciotti, Emanuele
Komarov, Anton
Libera, Stefano
Litunovsky, Nikolay
Makhankov, Alexey
Mancin, Andrea
Merola, Mario
Pizzuto, Aldo
Riccardi, Bruno
Roccella, Selanna
FUSION ENGINEERING AND DESIGN, 2011, 86 (9-11) : 1591 - 1594
[39] Fabrication and thermal cycle testing of a first wall mock-up for ITER baffle blanket module
Japan Atomic Energy Research Inst, Ibaraki-ken, Japan
Fusion Technol, 3 pt 2 (908-913):
[40] Fabrication and thermal cycle testing of a first wall mock-up for ITER baffle blanket module
Hatano, T
Suzuki, S
Yokoyama, K
Akiba, M
Ohmori, J
Kuroda, T
Takatsu, H
FUSION TECHNOLOGY, 1998, 34 (03): : 908 - 913

← 1 2 3 4 5 →