Physical, Mechanical and Electrical Properties of W-20 wt.% Cu Composite Produced by Liquid Phase Sintering Process

被引：0

作者：

Ismail, Fauzi ^{[1
]}

Selamat, Mohd Asri ^{[1
]}

Muhamad, Norhamidi ^{[2
]}

Sulong, Abu Bakar ^{[2
]}

Majid, Nurzirah Abdul ^{[1
]}

机构：

[1] SIRIM Berhad, Adv Mat Res Ctr AMREC, Struct Mat Program, Lot 34,Jalan Hitech 2-3,Kulim Hitech Pk, Kulim 09000, Kedah, Malaysia

[2] Univ Kebangsaan Malaysia, Dept Mech & Mat Engn, Bangi 43600, Selangor, Malaysia

来源：

ADVANCED MATERIALS CONFERENCE (AMC 2012) | 2014年 / 879卷

关键词：

compaction; liquid phase sintering; microstructure; porosity; densification;

D O I：

10.4028/www.scientific.net/AMR.879.21

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

In this study, the effect of sintering temperature on the properties of tungsten-copper (W-Cu) composite produced by liquid phase sintering (LPS) process has been investigated. W-20 wt.% Cu composite powders with particle size less than 1 mu m was prepared by cold compaction and followed by cold isostatic pressing. The green specimens were then sintered under nitrogen based atmosphere in the temperature range of 1100 degrees C to 1300 degrees C. The sintering studies were conducted to determine the extent of densification and corresponding to microstructure changes. In addition, the properties of the sintered specimens such as physical appearance, microstructure evolution, mechanical and electrical properties were presented and discussed.

引用

页码：21 / +

页数：3

共 50 条

[41] Effect of sintering temperature on phase evolution, microstructure, and mechanical properties of La2Ce2O7/40 wt.% YSZ composite ceramics
Parchovianska, Ivana
Parchoviansky, Milan
Nowicka, Aleksandra
Prnova, Anna
Svancarek, Peter
Pakseresht, Amirhossein
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2023, 24 : 4573 - 4586
[42] Effect of milling parameters on sinterability, mechanical and electrical properties of Cu-4 wt.% ZrO2 nanocomposite
Taha, Mohammed A.
Nassar, Amira H.
Zawrah, M. F.
MATERIALS CHEMISTRY AND PHYSICS, 2016, 181 : 26 - 32
[43] Effect of composition and pouring temperature of Cu(20-24)wt.%Sn by sand casting on fluidity and mechanical properties
Slamet, Sugeng
Suyitno
Kusumaningtyas, Indraswari
JOURNAL OF MECHANICAL ENGINEERING AND SCIENCES, 2019, 13 (04) : 6022 - 6035
[44] Effect of Milling Time and Process Control Agent on Microstructure and Mechanical Properties of AA2024-2 wt.% Cu Metal-Metal Composites Produced by Mechanical Alloying
Gultekin, Gul Gedik
Canakci, Aykut
Canpolat, Ozlem
METALLOGRAPHY MICROSTRUCTURE AND ANALYSIS, 2023, 12 (03) : 444 - 454
[45] Simulation of densification process of W-Cu system during liquid-phase sintering
Qu, X.-H. (quxh@ustb.edu.cn), 1600, Central South University of Technology (24):
[46] 6.5wt% Si Electrical Sheet Produced by Laminar Composite Technique with Thermo-mechanical Process
Ji, Shuai
2016 6TH INTERNATIONAL CONFERENCE ON INFORMATION TECHNOLOGY FOR MANUFACTURING SYSTEMS (ITMS 2016), 2016, : 11 - 13
[47] Preparation of highly dispersed superfine W–20 wt% Cu composite powder with excellent sintering property by highly concentrated wet ball-milled process
Bo-Hua Duan
Zhen Fu
Cheng-Kang Qi
Hui-Jiang Liu
Ao-Kui Sun
De-Zhi Wang
Rare Metals, 2018, 37 : 961 - 967
[48] Influence of sintering process on mechanical properties of SiCpAl composite produced by powder metallurgy after extruding
Jia, Yuxi
Jinshu Rechuli/Heat Treatment of Metals, 2000, (03): : 13 - 14
[49] Mechanochemical process for W-15 wt.%Cu nanocomposite powders with WO3-CuO powder mixture and its sintering characteristics
Kim, DG
Lee, BH
Oh, ST
Do Kim, Y
Kang, SG
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2005, 395 (1-2): : 333 - 337
[50] Structure, physical and mechanical properties of TiB-40 wt.%Ti composite materials obtained by unrestricted SHS compression
Bazhin, Pavel
Konstantinov, Alexander
Chizhikov, Andrey
Prokopets, Arina
Bolotskaia, Anastasia
MATERIALS TODAY COMMUNICATIONS, 2020, 25

← 1 2 3 4 5 →