Drilling Process on CFRP: Multi-Criteria Decision-Making with Entropy Weight Using Grey-TOPSIS Method

被引:17
|
作者
Tran, Quang-Phuoc [1 ]
Nguyen, Van-Nhat [2 ]
Huang, Shyh-Chour [1 ]
机构
[1] Natl Kaohsiung Univ Appl Sci, Dept Mech Engn, Kaohsiung 80778, Taiwan
[2] Hung Yen Univ Technol & Educ, Fac Mech Engn, Hung Yen 160000, Vietnam
来源
APPLIED SCIENCES-BASEL | 2020年 / 10卷 / 20期
关键词
CFRP; uncut fiber; delamination; entropy weight; TOPSIS; PROCESS PARAMETERS; MULTIOBJECTIVE OPTIMIZATION; MACHINING PARAMETERS; SELECTION; COMPOSITE; DELAMINATION; ALGORITHM; CRITERIA; COOLANT;
D O I
10.3390/app10207207
中图分类号
O6 [化学];
学科分类号
0703 ;
摘要
Moisture strongly affects the quality and mechanical specificity of carbon fiber reinforced plastic (CFRP) when using lubrication fluids during machining, and the significant impact of the cutting tool geometry and cryogenic gas cooling on CFRP machining capabilities are observed. The main body of this paper aims at making decisions about the optimum parameter of the drilling process while machining on CFRP base on the grey relational coefficient embed to the technique for order of preference by similarity to an ideal solution (Grey-TOPSIS). The entropy method was used to determine the weight of decision-making for handling a multiple measure decision-making response. The twist angle of the tool drill, lubrication, and feed rate were used as the input variables, and were analyzed while taking into account several multi-response outputs, such as the surface roughness, uncut fiber, and delamination. The result showed that a feed rate of 228 mm/min, the high-helix twist angle, and cryogenic CO2 lubrication leads the calculated value to close the relative value, which minimizes the value of the surface roughness, the uncut fiber, and the delamination. Finally, verification of the valid effect of each parameter process was conducted using analysis of variance. The results indicated that the lubrication was the highest remarkable criterion on the uncut fiber, the delamination, and the surface roughness. By integrating the advantage of grey systems theory, and the technique for order preference by similarity to an ideal solution, to evaluate and optimize the machining parameter, the results indicate that the proposed model is useful to facilitate the multi-criteria decision-making problem under the environment of uncertainty and vagueness. This relatively advanced approach is very effectual in rejecting process variation and a great assistive strategy than other multi-criteria decision-making approaches.
引用
收藏
页码:1 / 18
页数:18
相关论文
共 50 条
  • [21] A multi-criteria decision-making in turning process using the MAIRCA, EAMR, MARCOS and TOPSIS methods: A comparative study
    Trung, D. D.
    Thinh, H. X.
    ADVANCES IN PRODUCTION ENGINEERING & MANAGEMENT, 2021, 16 (04): : 443 - 456
  • [22] Multi-Criteria Decision Making in the PMEDM Process by Using MARCOS, TOPSIS, and MAIRCA Methods
    Nguyen, Huu-Quang
    Nguyen, Van-Tung
    Phan, Dang-Phong
    Tran, Quoc-Hoang
    Vu, Ngoc-Pi
    APPLIED SCIENCES-BASEL, 2022, 12 (08):
  • [23] When is a Decision-Making Method Trustworthy? Criteria for Evaluating Multi-Criteria Decision-Making Methods
    Saaty, Thomas L.
    Ergu, Daji
    INTERNATIONAL JOURNAL OF INFORMATION TECHNOLOGY & DECISION MAKING, 2015, 14 (06) : 1171 - 1187
  • [24] A fuzzy multi-criteria emergency decision-making method
    Wu, Wen-Shuai
    Kou, Gang
    Peng, Yi
    Shi, Yong
    Xitong Gongcheng Lilun yu Shijian/System Engineering Theory and Practice, 2012, 32 (06): : 1298 - 1304
  • [25] Fuzzy α-discounting method for multi-criteria decision-making
    Karaman, Atilla
    Dagdeviren, Metin
    JOURNAL OF THE CHINESE INSTITUTE OF ENGINEERS, 2015, 38 (07) : 855 - 865
  • [26] Multiplicative multi-criteria analysis method for decision-making
    Zizovic, Miodrag M.
    Damljanovic, Nada
    Zizovic, Malisa R.
    MAEJO INTERNATIONAL JOURNAL OF SCIENCE AND TECHNOLOGY, 2016, 10 (02) : 233 - 241
  • [27] Multi-Criteria Decision-Making Using Connection Number Based TOPSIS Method Under Tripolar Fuzzy Environment
    Arif, Waqar
    Khan, Waheed Ahmad
    Khan, Asghar
    Le, Ha Viet
    Tran, Nhung Thi
    Pham, Hai Van
    IEEE ACCESS, 2024, 12 : 142127 - 142140
  • [28] Multi-criteria fuzzy decision-making method based on cross entropy and score functions
    Wang, Jian-qiang
    Li, Jing-jing
    EXPERT SYSTEMS WITH APPLICATIONS, 2011, 38 (01) : 1032 - 1038
  • [29] The Linguistic Picture Fuzzy Set and Its Application in Multi-Criteria Decision-Making: An Illustration to the TOPSIS and TODIM Methods Based on Entropy Weight
    Liu, Donghai
    Luo, Yan
    Liu, Zaiming
    SYMMETRY-BASEL, 2020, 12 (07):
  • [30] Multi-Criteria Decision Making in the Milling Process Using the PARIS Method
    Le, Hong Ky
    ENGINEERING TECHNOLOGY & APPLIED SCIENCE RESEARCH, 2022, 12 (05) : 9208 - 9216