A new high sensitivity thermoluminescent phosphor with low residual signal and good stability to heat treatment:: LiF:Mg,Cu,Na,Si

被引:15
|
作者
Tang, K [1 ]
Zhu, H [1 ]
Shen, W [1 ]
Liu, B [1 ]
机构
[1] Solid Dosimetr Detector & Method Lab, Beijing 102205, Peoples R China
关键词
D O I
10.1093/oxfordjournals.rpd.a005855
中图分类号
X [环境科学、安全科学];
学科分类号
08 ; 0830 ;
摘要
The preliminary investigations are reported on the characteristics of a new. high-sensitivity thermoluminescence phosphor material (LiF:Mg,Cu,Na,Si) prepared in this laboratory. The main dosimetric peak of this phosphor occurs at 197degreesC at a heating rate of 1degreesC.s(-1). The glow curve shape shows minimal differences and sensitivity remains stable when annealed in the range from 250 to 280 C for 10 min. Its TL sensitivity to gamma radiation is about 30 times higher than that of TLD-100 with a residual signal 0.2% following a 260degreesC readout at a heating rate of 15degreesC.s(-1). This negligible residual signal renders LiF:Mg,Cu,Na,Si usable in unannealed form. Its TL response at both 260degreesC and 280degreesC are reproducible within a coefficient of variation of 2% over ten re-use cycles without systematic decrease. It retains the main advantages of LiF:Mg,Cu,P phosphor, and has a lower residual signal and a better stability to heat treatment.
引用
收藏
页码:239 / 242
页数:4
相关论文
共 48 条
  • [41] Novel high strength Al-10.5Si-3.4Cu-0.2Mg alloy produced through two-stage solution heat treatment
    Abdi, Mohsen
    Shabestari, Saeed G.
    TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, 2021, 31 (03) : 576 - 585
  • [42] Improved stress relaxation stability of a heat-resistant Al-Cu-Mg-Ag alloy with good mechanical properties by a pre-annealing/solution-aging treatment
    Zhao, Ziyao
    Xiao, Namin
    Zhang, Zhihao
    Wang, Zhilei
    JOURNAL OF ALLOYS AND COMPOUNDS, 2023, 961
  • [43] Effects of Heat Treatment on the Microstructures and High Temperature Mechanical Properties of Hypereutectic Al–14Si–Cu–Mg Alloy Manufactured by Liquid Phase Sintering Process
    Joon-Young Heo
    Jin-Han Gwon
    Jong-Kwan Park
    Kee-Ahn Lee
    Metals and Materials International, 2018, 24 : 586 - 596
  • [44] Effects of Heat Treatment on the Microstructures and High Temperature Mechanical Properties of Hypereutectic Al-14Si-Cu-Mg Alloy Manufactured by Liquid Phase Sintering Process
    Heo, Joon-Young
    Gwon, Jin-Han
    Park, Jong-Kwan
    Lee, Kee-Ahn
    METALS AND MATERIALS INTERNATIONAL, 2018, 24 (03) : 586 - 596
  • [45] Effect of Er Addition on the High Temperature Strength of Al-Si-Cu-Ni-Mg-Fe Piston Alloys by T5 and T6 Heat Treatment
    Li, Xianfeng
    Xia, Cunjuan
    Wu, Yi
    Chen, Dong
    Wang, Mingliang
    Ma, Naiheng
    Wang, Haowei
    MATERIALS SCIENCE-MEDZIAGOTYRA, 2019, 25 (04): : 376 - 382
  • [46] Preparation of a novel ultra-high strength Al–Si–Cu–Ni alloy at room/elevated temperature by squeeze casting combined with a new heat treatment process
    Shulin Lü
    Shilong Li
    Zhaoxiang Yan
    Shusen Wu
    Jianyu Li
    Xiaoyuan Ji
    Progress in Natural Science:Materials International, 2024, 34 (04) : 690 - 701
  • [47] High hardness and retained austenite stability in Si- bearing hypereutectoid steel through new heat treatment design principles (vol 142, pg 279, 2018)
    Sourmail, T.
    Caballero, F. G.
    Moudian, F.
    De Castro, D.
    Benito, M.
    MATERIALS & DESIGN, 2018, 150 : 17 - 17
  • [48] Preparation of a novel ultra-high strength Al-Si-Cu-Ni alloy at room/elevated temperature by squeeze casting combined with a new heat treatment process
    Lu, Shulin
    Li, Shilong
    Yan, Zhaoxiang
    Wu, Shusen
    Li, Jianyu
    Ji, Xiaoyuan
    PROGRESS IN NATURAL SCIENCE-MATERIALS INTERNATIONAL, 2024, 34 (04) : 690 - 701