A new high sensitivity thermoluminescent phosphor with low residual signal and good stability to heat treatment:: LiF:Mg,Cu,Na,Si

被引:15
|
作者
Tang, K [1 ]
Zhu, H [1 ]
Shen, W [1 ]
Liu, B [1 ]
机构
[1] Solid Dosimetr Detector & Method Lab, Beijing 102205, Peoples R China
关键词
D O I
10.1093/oxfordjournals.rpd.a005855
中图分类号
X [环境科学、安全科学];
学科分类号
08 ; 0830 ;
摘要
The preliminary investigations are reported on the characteristics of a new. high-sensitivity thermoluminescence phosphor material (LiF:Mg,Cu,Na,Si) prepared in this laboratory. The main dosimetric peak of this phosphor occurs at 197degreesC at a heating rate of 1degreesC.s(-1). The glow curve shape shows minimal differences and sensitivity remains stable when annealed in the range from 250 to 280 C for 10 min. Its TL sensitivity to gamma radiation is about 30 times higher than that of TLD-100 with a residual signal 0.2% following a 260degreesC readout at a heating rate of 15degreesC.s(-1). This negligible residual signal renders LiF:Mg,Cu,Na,Si usable in unannealed form. Its TL response at both 260degreesC and 280degreesC are reproducible within a coefficient of variation of 2% over ten re-use cycles without systematic decrease. It retains the main advantages of LiF:Mg,Cu,P phosphor, and has a lower residual signal and a better stability to heat treatment.
引用
收藏
页码:239 / 242
页数:4
相关论文
共 48 条
  • [31] Achievement of High Strength and Ductility in Al-Si-Cu-Mg Alloys by Intermediate Phase Optimization in As-Cast and Heat Treatment Conditions
    Zhang, Bingrong
    Zhang, Lingkun
    Wang, Zhiming
    Gao, Anjiang
    MATERIALS, 2020, 13 (03)
  • [32] The heat treatment of rheo-high pressure die cast 6xxx series Al-Mg-Si-(Cu) alloys
    Moeller, Heinrich
    Daswa, Pfarelo
    Govender, Gonasagren
    ALUMINIUM ALLOYS 2014 - ICAA14, 2014, 794-796 : 137 - 142
  • [33] A novel Na2MoO4@CNT/Al-Zn-Mg-Cu composite with superior corrosion resistance and good mechanical properties: Effect of heat treatment
    Yang, Jie
    Li, Qing
    Xiao, Zhixiang
    Wang, Zhengbin
    Liu, Zhenyu
    Xiao, Bolv
    Ma, Zongyi
    Zheng, Yugui
    JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2025, 35 : 2826 - 2839
  • [34] Heat treatment of the new high-strength high-ductility Al-Mg-Si-Mn alloys with Sc, Zr and Cr additions
    Trudonoshyn, O.
    Prach, O.
    Randelzhofer, P.
    Durst, K.
    Koerner, C.
    MATERIALIA, 2021, 15
  • [35] Role of heat treatment in the improvement of mechanical properties of a high-quality Al-11Si-1.5Cu-0.3Mg casting alloy
    Tao Lu
    Ji-li Wu
    Ye Pan
    Shi-wen Tao
    Yu Chen
    ChinaFoundry, 2015, 12 (02) : 111 - 117
  • [36] Research Progress on Multi-Component Alloying and Heat Treatment of High Strength and Toughness Al-Si-Cu-Mg Cast Aluminum Alloys
    Zhang, Mingshan
    Tian, Yaqiang
    Zheng, Xiaoping
    Zhang, Yuan
    Chen, Liansheng
    Wang, Junsheng
    MATERIALS, 2023, 16 (03)
  • [37] Role of heat treatment in the improvement of mechanical properties of a high-quality Al-11Si-1.5Cu-0.3Mg casting alloy
    Tao Lu
    Ji-li Wu
    Ye Pan
    Shi-wen Tao
    Yu Chen
    China Foundry, 2015, (02) : 111 - 117
  • [38] Role of heat treatment in the improvement of mechanical properties of a high-quality Al-11Si-1.5Cu-0.3Mg casting alloy
    Lu, Tao
    Wu, Ji-li
    Pan, Ye
    Tao, Shi-wen
    Chen, Yu
    CHINA FOUNDRY, 2015, 12 (02) : 111 - 117
  • [39] High hardness and retained austenite stability in Si-bearing hypereutectoid steel through new heat treatment design principles
    Sourmail, T.
    Caballero, F. G.
    Moudian, F.
    De Castro, D.
    Benito, M.
    MATERIALS & DESIGN, 2018, 142 : 279 - 287
  • [40] Room and high temperature fatigue behaviour of the A354 and C355 (Al-Si-Cu-Mg) alloys: Role of microstructure and heat treatment
    Ceschini, Lorella
    Morri, Alessandro
    Toschi, Stefania
    Seifeddine, Salem
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 653 : 129 - 138