Effects of the heterogeneity in the electron beam welded joint on fatigue crack growth in Ti-6Al-4V alloy

被引：39

作者：

Li, Xingzhi ^{[1
]}

Hu, Shubing ^{[1
]}

Xiao, Jianzhong ^{[1
]}

Ji, Longbo ^{[1
]}

机构：

[1] Huazhong Univ Sci & Technol, State Key Lab Mat Proc & Die Mould Technol, Wuhan 430074, Peoples R China

来源：

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2011年 / 529卷

关键词：

Titanium alloys; Fatigue; Heterogeneity; Electron beam welding; TITANIUM-ALLOY; RESIDUAL-STRESS; MICROSTRUCTURE; BEHAVIOR; PROPAGATION; FRACTURE; PLATE;

D O I：

10.1016/j.msea.2011.09.014

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

The heterogeneity of electron beam (EB)-welded joints in thick Ti-6Al-4V alloy plates is defined and described. The microstructure, hardness, and fatigue crack growth rate (FCGR) in the fuse zone (FZ) and the heat-affected zone (HAZ) of thick Ti-6Al-4V alloy EB-welded joint are studied using a new testing and interception method. The fatigue fractographs, crack growth paths and the microscopic deformation are observed through scanning and transmission electron microscopy. The effect mechanism of heterogeneity in the electron beam weld joint to FCGRs is discussed. The results reveal that FCGR is higher in the HAZ than in the FZ, mainly because of the effect of heterogeneity! of the welded joint. Heterogeneity II increases from the top to the root of the welding seam while the size of the alpha' phase decreases. Consequently, FCGR is higher at the root of the welding seam. Heterogeneity in the joint is found to greatly influence the FCGR. Crown Copyright (C) 2011 Published by Elsevier B.V. All rights reserved.

引用

页码：170 / 176

页数：7

共 50 条

[31] MICROSTRUCTURAL INFLUENCES ON FATIGUE CRACK GROWTH IN TI-6AL-4V
IRVING, PE
BEEVERS, CJ
MATERIALS SCIENCE AND ENGINEERING, 1974, 14 (03): : 229 - 238
[32] MECHANISMS OF CLEAVAGE DURING FATIGUE CRACK-GROWTH IN TI-6AL-4V ALLOY
RAVICHANDRAN, KS
DWARAKADASA, ES
BANERJEE, D
SCRIPTA METALLURGICA ET MATERIALIA, 1991, 25 (09): : 2115 - 2120
[33] Fatigue life evaluation of Ti-6Al-4V welded joints manufactured by electron beam melting
Hu, Yanan
Wu, Shengchuan
Xie, Cheng
Wu, Wenwang
Zhang, Jie
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES, 2021, 44 (08) : 2210 - 2221
[34] Inhomogeneous Fatigue Characteristics of Welded Ti-6Al-4V Thick Plate by the Electron Beam Method
Wang, Haiyan
Zeng, Caiyou
Zhang, Yupeng
Zhou, Yu
Dong, Chunlin
METALS AND MATERIALS INTERNATIONAL, 2021, 27 (11) : 4527 - 4535
[35] Long crack growth mechanisms in Ti-6Al-4V alloy
Goswami, T
INDIAN JOURNAL OF ENGINEERING AND MATERIALS SCIENCES, 2005, 12 (05) : 367 - 375
[36] MECHANICAL-PROPERTIES OF ELECTRON-BEAM WELDED JOINT IN SOLUTION TREATED AND AGED TI-6AL-4V ALLOY
FUJITA, M
KAWABE, Y
IRIE, H
TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1986, 72 (06): : 678 - 684
[37] Effects of laser peening on residual stresses and fatigue crack growth properties of Ti-6Al-4V titanium alloy
Zhou, J. Z.
Huang, S.
Zuo, L. D.
Meng, X. K.
Sheng, J.
Tian, Q.
Han, Y. H.
Zhu, W. L.
OPTICS AND LASERS IN ENGINEERING, 2014, 52 : 189 - 194
[38] Microstructure evolution and fatigue crack growth of diffusion bonded Ti-6Al-4V titanium alloy
Li, Tianle
Zhong, Lixin
Wu, Huiping
An, Dayong
Li, Xifeng
Chen, Jun
JOURNAL OF ALLOYS AND COMPOUNDS, 2022, 918
[39] Fusion zone microstructure and fatigue crack growth behaviour in Ti-6Al-4V alloy weldments
Murthy, KK
Potluri, NB
Sundaresan, S
MATERIALS SCIENCE AND TECHNOLOGY, 1997, 13 (06) : 503 - 510
[40] FRACTURE MODE TRANSITIONS DURING FATIGUE CRACK-GROWTH IN TI-6AL-4V ALLOY
RAVICHANDRAN, KS
SCRIPTA METALLURGICA ET MATERIALIA, 1990, 24 (07): : 1275 - 1280

← 1 2 3 4 5 →