Improving metal-ceramic systems subjected to sliding contact by reinforcing the metallic counterpart with ceramic particles

被引：6

作者：

Kan, Wen Hao ^{[1
,2
,3
,4
]}

Huang, Siyu ^{[1
]}

Proust, Gwenaelle ^{[5
]}

Bhatia, Vijay ^{[2
]}

Chang, Li ^{[1
]}

Lucey, Timothy ^{[6
]}

Tang, Xinhu ^{[6
]}

Cairney, Julie M. ^{[1
,2
]}

机构：

[1] Univ Sydney, Sch Aerosp Mech & Mechatron Engn, Sydney, NSW 2006, Australia

[2] Univ Sydney, Australian Ctr Microscopy & Microanal, Sydney, NSW 2006, Australia

[3] Monash Ctr Addit Mfg, Notting Hill, Vic 3168, Australia

[4] Monash Univ, Dept Mat Sci & Engn, Clayton, Vic 3800, Australia

[5] Univ Sydney, Sch Civil Engn, Sydney, NSW 2006, Australia

[6] Weir Minerals Australia, Artarmon, NSW 2064, Australia

来源：

WEAR | 2020年 / 452卷

基金：

澳大利亚研究理事会;

关键词：

Sliding wear; Stainless steel; Metal-matrix composite; Bearings; Advanced ceramics; WEAR BEHAVIOR; SILICON-NITRIDE; TRIBOLOGICAL BEHAVIOR; STEEL; MICROSTRUCTURE; MECHANISMS; FRICTION; ZIRCONIA; ALUMINA;

D O I：

10.1016/j.wear.2020.203311

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

The study of sliding wear is important as it occurs in many industrial mechanical systems. In metal-ceramic sliding wear, reinforcing the metallic counterpart with ceramic particles transforms the system from a pure metal-ceramic interaction to one that contains both metal-ceramic and ceramic-ceramic interactions, which may improve the wear performance of both materials involved. This study shows that incorporating NbC particles into a bearing stainless steel reduces its wear rate against SiC, WC and Al2O3 counterparts but its wear rate remained unchanged against ZrO2. For the ceramic counterparts, SiC and WC also experienced reduced wear while Al2O3 showed negligible wear across all tests. ZrO2, on the other hand, experienced a very high level of wear when the stainless steel contained 5 vol% NbC but the wear rate gradually decreased as the volume fraction of NbC increased to 15 vol%. Higher NbC volume fractions are thus expected to yield further improvement.

引用

页数：13

共 50 条

[41] Interfacial structures developed by firing metal-ceramic dental systems
Darcozi, L.
Hegedus, Cs.
Kokenyesi, V.
Beke, D. L.
FUNCTIONAL MATERIALS AND DEVICES, 2006, 517 : 153 - 158
[42] THE INFLUENCE OF CRYSTALLOGRAPHY AND OXIDE AND METALLIC TYPES ON THE STRUCTURE AND PROPERTIES OF METAL-CERAMIC INTERFACES
YANG, JC
LU, YC
SASS, SL
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1993, 162 (1-2): : 97 - 106
[43] Metal-Ceramic Compatibility in Dental Restorations According to the Metallic Component Manufacturing Procedure
Dawod, Nazem
Miculescu, Marian
Antoniac, Iulian Vasile
Miculescu, Florin
Agop-Forna, Doriana
MATERIALS, 2023, 16 (16)
[44] Simultaneous measurement of contact angles and work of adhesion in metal-ceramic systems by the immersion-emersion technique
Rivollet, I., 1600, (25):
[45] SLIDING WEAR OF METAL - CERAMIC SYSTEMS WITH OSCILLATING LOAD
FELLER, HG
WIENSTROTH, U
ZEITSCHRIFT FUR METALLKUNDE, 1989, 80 (05): : 352 - 358
[46] Comparison of the marginal fit of different all-ceramic and metal-ceramic crown systems: an in vitro study
Polansky, R.
Heschl, A.
Arnetzl, G.
Haas, M.
Wegscheider, W.
INTERNATIONAL JOURNAL OF STOMATOLOGY & OCCLUSION MEDICINE, 2010, 3 (02) : 106 - 110
[47] Effect of different air-abrasion particles on metal-ceramic bond strength
Kulunk, Tolga
Kurt, Murat
Ural, Cagri
Kulunk, Safak
Baba, Seniha
JOURNAL OF DENTAL SCIENCES, 2011, 6 (03) : 140 - 146
[48] Spatial Tailoring of a Metal-Ceramic Composite Pane Subjected to High-Speed Flow
Deierling, Phillip E.
Zhupanska, Olesya, I
Pasiliao, Crystal L.
JOURNAL OF AEROSPACE ENGINEERING, 2021, 34 (01)
[49] SOLID-SOLID INTERFACIAL ENERGY DETERMINATIONS IN METAL-CERAMIC SYSTEMS
PILLIAR, RM
NUTTING, J
PHILOSOPHICAL MAGAZINE, 1967, 16 (139): : 181 - &
[50] Difference between selected and obtained shade for metal-ceramic crown systems
Omar, H.
Atta, O.
El-Mowafy, O.
OPERATIVE DENTISTRY, 2008, 33 (05) : 502 - 507

← 1 2 3 4 5 →