Effect of the different additives on the fabrication of porous kaolin-based mullite ceramics

被引：61

作者：

Hou, Zhaoping ^{[1
]}

Cui, Bingxia ^{[1
]}

Liu, Liangliang ^{[1
]}

Liu, Qiang ^{[2
]}

机构：

[1] Taiyuan Univ Technol, Coll Mat Sci & Engn, Taiyuan 030024, Peoples R China

[2] Harbin Inst Technol, Sch Mat Sci & Engn, Harbin 150001, Peoples R China

来源：

CERAMICS INTERNATIONAL | 2016年 / 42卷 / 15期

基金：

中国国家自然科学基金;

关键词：

Kaolin; Mullite; Porosity; Grain morphology; MEMBRANE SUPPORTS; FLY-ASH; WHISKERS; TRANSFORMATION; KINETICS; GROWTH;

D O I：

10.1016/j.ceramint.2016.08.020

中图分类号：

TQ174 [陶瓷工业]; TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

Porous mullite ceramics were prepared from kaolin and Al2O3 with different sintering additives TiO2, MgO and MoO3. The sintering aids have a significant influence on the grain morphology and densification process by varying the composition and viscosity of liquid phase during firing. The addition of TiO2 retarded the mullite transformation. The introduction of MgO promoted the secondary mullite transformation and the formation of needle-like mullite grains. Compared with MgO, the samples with MoO3 have lower secondary mullitization temperature. The lower secondary mullitization temperature was beneficial for the secondary mullite to grow anisotropically and then to hinder shrinkage during the sintering process. Thereby, the samples with MoO3 showed a network skeleton structure which consists of acicular mullite grains and exhibited a highly open porosity of 67%. (C) 2016 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

引用

页码：17254 / 17258

页数：5

共 50 条

[41] DSC and TGA of a Kaolin-Based Ceramics with Zeolite Addition During Heating up to 1100 °C
Sunitrova, Ivana
Trnik, Anton
THERMOPHYSICS 2018, 2018, 1988
[42] Fabrication of Porous Mullite Ceramics with High Porosity Using Foam-gelcasting
Yang, Fengkun
Li, Cuiwei
Lin, Yamei
Wang, Chang-an
HIGH-PERFORMANCE CERAMICS VII, PTS 1 AND 2, 2012, 512-515 : 580 - +
[43] Recycling of waste red mud for fabrication of SiC/mullite composite porous ceramics
Wang, Wei
Chen, Weijie
Liu, Haitao
CERAMICS INTERNATIONAL, 2019, 45 (08) : 9852 - 9857
[44] DC conductivity of kaolin-based ceramics in the temperature range 20-600 degrees C
Trnovcova, Viera
Podoba, Rudolf
Stubna, Igor
EPITOANYAG-JOURNAL OF SILICATE BASED AND COMPOSITE MATERIALS, 2012, 64 (3-4): : 46 - 49
[45] Hot forging of mullite-based ceramics prepared from kaolin-alumina
Ohashi, M
Iida, Y
JOURNAL OF THE AMERICAN CERAMIC SOCIETY, 2000, 83 (07) : 1825 - 1827
[46] Fabrication and properties of mullite fiber matrix porous ceramics by a TBA-based gel-casting process
Hou, Zhenguang
Du, Haiyan
Liu, Jiachen
Hao, Ruihua
Dong, Xue
Liu, Mengxia
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY, 2013, 33 (04) : 717 - 725
[47] Statistical Design for Recycling Kaolin Processing Waste in the Manufacturing of Mullite-Based Ceramics
Menezes, Romualdo Rodrigues
Brasileiro, Maria Isabel
Goncalves, Wherllyson Patricio
de Lima Santana, Lisiane Navarro
Neves, Gelmires Araujo
Ferreira, Heber Sivini
Ferreira, Heber Carlos
MATERIALS RESEARCH-IBERO-AMERICAN JOURNAL OF MATERIALS, 2009, 12 (02): : 201 - 209
[48] Hot forging of mullite-based ceramics prepared from kaolin-alumina
Ohashi, Masayoshi, 1825, American Ceramic Soc, Westerville (83):
[49] Thermal Conductivity of Very Porous Kaolin- Based Ceramics
Bourret, Julie
Michot, Aurelie
Tessier-Doyen, Nicolas
Nait-Ali, Benoit
Pennec, Fabienne
Alzina, Arnaud
Vicente, Jerome
Peyratout, Claire S.
Smith, David S.
JOURNAL OF THE AMERICAN CERAMIC SOCIETY, 2014, 97 (03) : 938 - 944
[50] Fabrication and properties of porous anorthite/mullite ceramics with both high porosity and high strength
Wu, Linghao
Li, Cuiwei
Yang, Jing
Li, Hao
INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY, 2019, 16 (06) : 2197 - 2205

← 1 2 3 4 5 →