AFM in surface finishing: Part IV. Force-distance curves

被引：8

作者：

Smith, JR ^{[1
]}

Breakspear, S ^{[1
]}

Fletcher, RJR ^{[1
]}

Campbell, SA ^{[1
]}

机构：

[1] Univ Portsmouth, Sch Pharm & Biomed Sci, Appl Electrochem Grp, Portsmouth PO1 2DT, Hants, England

来源：

TRANSACTIONS OF THE INSTITUTE OF METAL FINISHING | 2005年 / 83卷 / 02期

关键词：

D O I：

10.1179/002029605X38979

中图分类号：

O646 [电化学、电解、磁化学];

学科分类号：

081704 ;

摘要：

The use of atomic surface microscope (AFM) to probe surfaces to obtain local physical information by the acquisition of force-distance curves was discussed. It was found that as the AFM tip approaches the surface of interest, the force-distance trace was usually flat (gradient = 0). It was also found that at any point on the loading curve the applied load can be reduced by pulling the probe away from the surface. The results show that AFM is a high resolution imaging tool that can be used to obtain information about surface finishing.

引用

页码：63 / 67

页数：5

共 50 条

[31] Improved algorithm to extract force-distance curves from scanning force microscope data
Eppell, SJ
Todd, BA
Zypman, FR
MATERIALS ISSUES AND MODELING FOR DEVICE NANOFABRICATION, 2000, 584 : 189 - 194
[32] Study of Micro- and Nanoscale Wetting Properties of Lubricants Using AFM Force-Distance Curves (vol 68, 36, 2020)
Friedrich, Sebastian
Cappella, Brunero
TRIBOLOGY LETTERS, 2021, 69 (04)
[33] AFM in surface finishing: Part III. Lateral force microscopy and friction measurements
Breakspear, S
Smith, JR
Campbell, SA
TRANSACTIONS OF THE INSTITUTE OF METAL FINISHING, 2003, 81 : B68 - B70
[34] Optimizing the accuracy of viscoelastic characterization with AFM force-distance experiments in the time and frequency domains
McCraw, Marshall R.
Uluutku, Berkin
Solomon, Halen D.
Anderson, Megan S.
Sarkar, Kausik
Solares, Santiago D.
SOFT MATTER, 2023, 19 (03) : 451 - 467
[35] AFM in surface finishing: Part II. Surface roughness
Smith, JR
Breakspear, S
Campbell, SA
TRANSACTIONS OF THE INSTITUTE OF METAL FINISHING, 2003, 81 : B55 - B58
[36] AFM in surface finishing: Part I. An introduction
Smith, JR
Breakspear, S
Campbell, SA
TRANSACTIONS OF THE INSTITUTE OF METAL FINISHING, 2003, 81 : B26 - B29
[37] Part I. An introduction AFM in surface finishing
Niemczewski, Bogdan
Finishing, 2003, 27 (05):
[38] Multiparametric high-resolution imaging of native proteins by force-distance curve–based AFM
Moritz Pfreundschuh
David Martinez-Martin
Estefania Mulvihill
Susanne Wegmann
Daniel J Muller
Nature Protocols, 2014, 9 : 1113 - 1130
[39] AFM force-distance curve methods for measuring the kinetics of silicon chemical etching and reactions between silylating agents and a silicon surface
Center for Photochemical Sciences, Bowling Green State University, Bowling Green, OH 43403, United States
Langmuir, 6 (2077-2079):
[40] AFM force-distance curve methods for measuring the kinetics of silicon chemical etching and reactions between silylating agents and a silicon surface
Grinevich, O
Mejiritski, A
Neckers, DC
LANGMUIR, 1999, 15 (06) : 2077 - 2079

← 1 2 3 4 5 →