MECHANICAL BEHAVIOR OF TiN/TiC-n MULTILAYER COATINGS AND Ti(C,N) MULTICOMPONENT COATINGS PRODUCED BY PACVD

被引：26

作者：

Azadi, M. ^{[1
]}

Rouhaghdam, A. S. ^{[2
]}

Ahangarani, S. ^{[3
]}

机构：

[1] Semnan Univ, Fac Engn, Dept Mat Engn, Semnan, Iran

[2] Tarbiat Modares Univ, Fac Engn, Dept Mat Engn, Surface Engn Lab, Tehran, Iran

[3] Iranian Res Org Sci & Technol, Adv Mat & Renewable Energies Dept, Tehran, Iran

来源：

STRENGTH OF MATERIALS | 2016年 / 48卷 / 02期

关键词：

multilayer coatings; multicomponent coatings; wear; fracture toughness; hardness; FRACTURE-TOUGHNESS; TRIBOLOGICAL BEHAVIOR; SLIDING WEAR; TOOL STEEL; TICN COATINGS; PLASMA; INDENTATION; TEMPERATURE; HARDNESS; FILMS;

D O I：

10.1007/s11223-016-9763-2

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

Mechanical properties of multilayer and multicomponent coatings were investigated in this paper. Titanium nitride/titanium carbide (TiN/TiC-n) multilayer and Ti(C,N) multicomponent coatings were prepared on the surface of AISI H13 hot work tool steel by the pulsed-DC plasma assisted chemical vapor deposition (PACVD). The microhardness, the toughness, the wear loss, and the friction coefficient were examined by Vickers hardness test and the pin-on-disk wear test. The optical microscopy was also used to examine worn surfaces and to characterize wear mechanisms. The results obtaiond show that multilayer coatings of TiN/TiC-10 have the lowest friction coefficient (as 0.2) and wear loss, the highest toughness (as 17. 7 MPa.m(1/2)) and microhardness (as 3150 VHN) among those values for multicomponent Ti(C,N) coatings and other multilayer coatings.

引用

页码：279 / 289

页数：11

共 50 条

[21] Microstructure and corrosion behavior of TiC/Ti(CN)/TiN multilayer CVD coatings on high strength steels
Zhang, Jin
Xue, Qi
Li, Songxia
APPLIED SURFACE SCIENCE, 2013, 280 : 626 - 631
[22] Tribology and microstructure of PACVD B-N-C coatings
Dekempeneer, E
Wagner, V
Gibson, P
Meneve, J
Kuypers, S
vanIjzendoorn, L
Smeets, J
Geurts, J
Caudano, R
DIAMOND FILMS AND TECHNOLOGY, 1997, 7 (03): : 181 - 193
[23] On the microstructure and deformation mechanisms under indentations of TiN/(Ti,Al)N multilayer coatings
Carvalho, NJM
Kooi, BJ
De Hosson, JTM
SURFACE TREATMENT VI: COMPUTER METHODS AND EXPERIMENTAL MEASUREMENTS FOR SURFACE TREATMENT EFFECTS, 2003, 7 : 233 - 242
[24] Tribological behavior of PACVD TiN coatings in the temperature range up to 500°C
Badisch, E
Fontalvo, GA
Stoiber, M
Mitterer, C
SURFACE & COATINGS TECHNOLOGY, 2003, 163 : 585 - 590
[25] Cathodic arc evaporation of (Ti,AI)N coatings and (Ti,AI)N/TiN multilayer-coatings-correlation between lifetime of coated cutting tools, structural and mechanical film properties
Weber, ER
Fontaine, F
Scheib, M
Bock, W
SURFACE & COATINGS TECHNOLOGY, 2004, 177 : 227 - 232
[26] Tribological behavior at elevated temperature of multilayer TiCN/TiC/TiN hard coatings produced by chemical vapor deposition
Bao, Mingdong
Xu, Xuebo
Zhang, Haijun
Liu, Xiaoping
Tian, Linhai
Zeng, Zhaoxin
Song, Yubin
THIN SOLID FILMS, 2011, 520 (02) : 833 - 836
[27] Ti(C, N) as Barrier Coatings
Banaszek, Katarzyna
Klimek, Leszek
COATINGS, 2019, 9 (07)
[28] Multilayer Ti-Cr-N coatings produced by the vacuum-arc deposition
Kunchenko, Yu. V.
Kunchenko, V. V.
Neklyudov, I. M.
Kartmazov, G. N.
Andreyev, A. A.
PROBLEMS OF ATOMIC SCIENCE AND TECHNOLOGY, 2007, (02): : 203 - 214
[29] Ti/TiN multilayer coatings: Deposition technique, characterization and mechanical properties
Dück, A.
Gamer, N.
Gesatzke, W.
Griepentrog, M.
Österle, W.
Sahre, M.
Urban, I.
Surface and Coatings Technology, 2001, 142-144 : 579 - 584
[30] Ti/TiN multilayer coatings:: deposition technique, characterization and mechanical properties
Dück, A
Gamer, N
Gesatzke, W
Griepentrog, M
Österle, W
Sahre, M
Urban, I
SURFACE & COATINGS TECHNOLOGY, 2001, 142 : 579 - 584

← 1 2 3 4 5 →