Properties of Soldering Cu/Fe Alloy Produced by Powder Metallurgy

被引：2
|
作者：
Sueyoshi, Hidekazu [1 ]
Ishii, Ryosuke [1 ]
Fukudome, Hisayoshi [1 ]
Mizokuchi, Shinji [2 ]
Wakabayashi, Toshio [2 ]
Saikusa, Kazuya [2 ]
机构：
[1] Kagoshima Univ, Grad Sch Sci & Engn, Kagoshima 8900065, Japan
[2] JAPAN UNIX Co Ltd, Techno Ctr, Kumamoto 8612202, Japan
来源：
MATERIALS TRANSACTIONS | 2008年 / 49卷 / 12期
关键词：
lead-free solder; copper/iron alloy; powder metallurgy; wettability; thermal conductivity;
D O I：
10.2320/matertrans.MRA2008112
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
In order to develop an advanced soldering material, the Cu/Fe alloys were produced by using powder metallurgy and the soldering properties were examined. Thermal conductivity of Cu/Fe alloy decreased with the increase in the volume fraction of pores, while it increased with the increase in the volume fraction of Cu particles. Wettability of Cu/Fe alloy was better than that of conventional Fe plating. Comparing the consumption amounts under the same wettability, the amount of Cu/Fe alloy consumed was smaller than that of Fe plating consumed. [doi: 10.2320/matertrans.MRA2008112]
引用
收藏
页码：2881 / 2886
页数：6
相关论文
共 50 条
  • [41] SINTERING PROCESS OF A HIGH PERMEABILITY NI-FE-CU-MO ALLOY MADE BY POWDER METALLURGY
    MURRELL, DL
    ENOCH, RD
    [J]. JOURNAL OF MATERIALS SCIENCE, 1970, 5 (06) : 478 - &
  • [42] Superplasticity in a powder metallurgy Al-Cu-Zr alloy
    Málek, P
    Cieslar, M
    Jezek, J
    [J]. PHYSICA STATUS SOLIDI A-APPLIED RESEARCH, 1999, 175 (02): : 467 - 480
  • [43] Characterization of fatigue properties of powder metallurgy titanium alloy
    Cao, Yuankui
    Zeng, Fanpei
    Liu, Bin
    Liu, Yong
    Lu, Jinzhong
    Gan, Ziyang
    Tang, Huiping
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 654 : 418 - 425
  • [44] Effects of process variables on the mechanical and physical properties of an Al–Cu–Mg powder metallurgy alloy
    B. D. Christensen
    I. W. Donaldson
    D. P. Bishop
    [J]. SN Applied Sciences, 2019, 1
  • [45] Creep behaviour and continuous precipitation of an aluminum alloy produced by powder metallurgy
    Evangelista, E
    Spigarelli, S
    Cerri, E
    Kloc, L
    Langdon, TG
    [J]. THERMEC '97 - INTERNATIONAL CONFERENCE ON THERMOMECHANICAL PROCESSING OF STEELS AND OTHER MATERIALS, VOLS I-II, 1997, : 995 - 1001
  • [46] Microstructure, Mechanical Properties, and Corrosion Behavior of Boron Carbide Reinforced Aluminum Alloy (Al-Fe-Si-Zn-Cu) Matrix Composites Produced via Powder Metallurgy Route
    Meignanamoorthy, M.
    Ravichandran, Manickam
    Mohanavel, Vinayagam
    Afzal, Asif
    Sathish, T.
    Alamri, Sagr
    Khan, Sher Afghan
    Saleel, C. Ahamed
    [J]. MATERIALS, 2021, 14 (15)
  • [47] Wear behavior of Al–Cu and Al–Cu/SiC components produced by powder metallurgy
    Adel Mahamood Hassan
    Ahmad Turki Mayyas
    Abdalla Alrashdan
    Mohammed T. Hayajneh
    [J]. Journal of Materials Science, 2008, 43 : 5368 - 5375
  • [48] Effect of sintering procedure on microstructure and mechanical properties of biomedical TiNbSn alloy produced via powder metallurgy
    Cakmak, Omer
    Kaya, Mehmet
    [J]. APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING, 2021, 127 (07):
  • [49] Microstructure and mechanical properties of a Pt-Rh alloy produced by powder metallurgy and subjected to plastic working
    Garbacz, H.
    Mizera, J.
    Laskowski, Z.
    Gierej, M.
    [J]. POWDER TECHNOLOGY, 2011, 208 (02) : 488 - 490
  • [50] Effect of sintering procedure on microstructure and mechanical properties of biomedical TiNbSn alloy produced via powder metallurgy
    Ömer Çakmak
    Mehmet Kaya
    [J]. Applied Physics A, 2021, 127
12345