Effect of plastic deformation on microstructure and hardness of 2024/3003 gradient composite ingot prepared by continuous casting

被引：6

作者：

Zhang, W. W. ^{[1
]}

Rohatgi, P. K. ^{[2
]}

Shao, M. ^{[1
]}

Li, Y. Y. ^{[1
]}

机构：

[1] S China Univ Technol, Sch Mech & Automot Engn, Guangzhou 510640, Peoples R China

[2] Univ Wisconsin, Coll Engn & Appl Sci, Milwaukee, WI 53211 USA

来源：

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2009年 / 505卷 / 1-2期

关键词：

Plastic deformation; Gradient composites; Continuous casting; Microstructure; Hardness; Bimetallic ingots; RESIDUAL-STRESS; FABRICATION;

D O I：

10.1016/j.msea.2008.11.003

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

The effects of plastic deformation on the evolution of microstructure and micro-hardness were studied on plates made from a cylindrical composite ingot of 2024/3003 aluminum alloys. This ingot was produced by double-stream-pouring continuous casting. The results show that the as-cast microstructure has a dominant influence on the evolution of microstructure and the distribution of micro-hardness of the composite ingot. The three layers in as-cast composite ingot were maintained after compression and roll processing. The micro-hardness in all three layers in the composite increased and the grain size in these layers appeared to decrease as the number of compression or rolling passes increased. The microstructure evolution in the direction parallel to the applied load can be evaluated qualitatively using a simplified lamination model. The distribution variation in micro-hardness measured along the direction normal to the applied load can be attributed to the movement of transition layer and diffusion of alloying elements. (C) 2008 Elsevier B.V. All rights reserved.

引用

页码：120 / 130

页数：11

共 45 条

[41] Effects of drawing speed on microstructure and properties of Cu-Ni-Si alloy clad AA8030 alloy composites prepared by continuous casting composite technology
Tian, Shuke
Zhao, Fan
Liu, Xinhua
[J]. Materials Today Communications, 2024, 40
[42] The Effect of Severe Plastic Deformation on the Microstructure and Mechanical Properties of Composite from 5056 and 1580 Aluminum Alloys Produced with Wire Arc Additive Manufacturing
Mavlyutov, Aydar
Evstifeev, Alexey
Volosevich, Darya
Gushchina, Marina
Voropaev, Artem
Zotov, Oleg
Klimova-Korsmik, Olga
[J]. METALS, 2023, 13 (07)
[43] In-situ TiB reinforced titanium matrix composite coatings prepared by laser cladding: Effect of TiB2 content on microstructure, hardness and wear properties
[J]. Ma, Lixia (maxia@bjut.edu.cn), 1600, Elsevier Ltd (1010):
[44] Effect of content of nano-ZrO2 on microstructure and micro-hardness of Ni-ZrO2 composite coatings prepared with electro-brush plating
College of Materials Science and Engineering, Henan Polytechnic University, Jiaozuo 454003, China
不详
不详
[J]. Cailiao Rechuli Xuebao, 2013, 6 (142-146):
[45] Effect of process parameters on micro hardness of Al-Al2O3 composite prepared using an alternative reinforced pattern in fused deposition modelling assisted investment casting
Singh, Sunpreet
Singh, Rupinder
[J]. ROBOTICS AND COMPUTER-INTEGRATED MANUFACTURING, 2016, 37 : 162 - 169

← 1 2 3 4 5 →