Effect of plastic deformation on microstructure and hardness of 2024/3003 gradient composite ingot prepared by continuous casting

被引：6
|
作者：
Zhang, W. W. [1 ]
Rohatgi, P. K. [2 ]
Shao, M. [1 ]
Li, Y. Y. [1 ]
机构：
[1] S China Univ Technol, Sch Mech & Automot Engn, Guangzhou 510640, Peoples R China
[2] Univ Wisconsin, Coll Engn & Appl Sci, Milwaukee, WI 53211 USA
来源：
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2009年 / 505卷 / 1-2期
关键词：
Plastic deformation; Gradient composites; Continuous casting; Microstructure; Hardness; Bimetallic ingots; RESIDUAL-STRESS; FABRICATION;
D O I：
10.1016/j.msea.2008.11.003
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
The effects of plastic deformation on the evolution of microstructure and micro-hardness were studied on plates made from a cylindrical composite ingot of 2024/3003 aluminum alloys. This ingot was produced by double-stream-pouring continuous casting. The results show that the as-cast microstructure has a dominant influence on the evolution of microstructure and the distribution of micro-hardness of the composite ingot. The three layers in as-cast composite ingot were maintained after compression and roll processing. The micro-hardness in all three layers in the composite increased and the grain size in these layers appeared to decrease as the number of compression or rolling passes increased. The microstructure evolution in the direction parallel to the applied load can be evaluated qualitatively using a simplified lamination model. The distribution variation in micro-hardness measured along the direction normal to the applied load can be attributed to the movement of transition layer and diffusion of alloying elements. (C) 2008 Elsevier B.V. All rights reserved.
引用
收藏
页码：120 / 130
页数：11
相关论文
共 45 条
  • [21] Evaluation of the effect of plastic deformation on the microstructure, hardness and magnetic properties of AISI type 316L stainless steel
    Mathias Marques, Allan Victor
    do Carmo, Kerciely Martins
    Lage, Wivyan Castro
    Perez Teixeira, Ricardo Luiz
    de Lacerda, Jose Carlos
    Soares Boucas Teixeira, Cynthia Helena
    Shitsuka, Ricardo
    [J]. MATERIA-RIO DE JANEIRO, 2020, 25 (02): : 1 - 10
  • [22] Effect of Plastic Hot Deformation on the Hardness and Continuous Cooling Transformations of 22MnB5 Microalloyed Boron Steel
    A. Barcellona
    D. Palmeri
    [J]. Metallurgical and Materials Transactions A, 2009, 40 : 1160 - 1174
  • [23] Effect of Plastic Hot Deformation on the Hardness and Continuous Cooling Transformations of 22MnB5 Microalloyed Boron Steel
    Barcellona, A.
    Palmeri, D.
    [J]. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2009, 40A (05): : 1160 - 1174
  • [24] Effect of reheating temperature on the microstructure and tensile properties of SiCP/2024Al composite prepared by powder thixoforming
    Li, P. B.
    Chen, T. J.
    [J]. POWDER METALLURGY, 2016, 59 (04) : 288 - 300
  • [25] Microstructure and hot deformation behaviour of high-carbon steel/low-carbon steel bimetal prepared by centrifugal composite casting
    Xu, Jianzhong
    Gao, Xingjian
    Jiang, Zhengyi
    Wei, Dongbin
    Jiao, Sihai
    [J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2016, 86 (1-4): : 817 - 827
  • [26] Microstructure and Mechanical Properties of a Near-α-Titanium-Alloy/TiB Composite Prepared in situ by Casting and Subjected to Deformation and Heat Treatment
    R. A. Gaisin
    V. M. Imayev
    R. M. Imayev
    [J]. Physics of Metals and Metallography, 2018, 119 : 907 - 916
  • [27] Microstructure and hot deformation behaviour of high-carbon steel/low-carbon steel bimetal prepared by centrifugal composite casting
    Jianzhong Xu
    Xingjian Gao
    Zhengyi Jiang
    Dongbin Wei
    Sihai Jiao
    [J]. The International Journal of Advanced Manufacturing Technology, 2016, 86 : 817 - 827
  • [28] Microstructure and Mechanical Properties of a Near-α-Titanium-Alloy/TiB Composite Prepared in situ by Casting and Subjected to Deformation and Heat Treatment
    Gaisin, R. A.
    Imayev, V. M.
    Imayev, R. M.
    [J]. PHYSICS OF METALS AND METALLOGRAPHY, 2018, 119 (09): : 907 - 916
  • [29] The effect of pressure and pouring temperature on the porosity, microstructure, hardness and yield stress of AA2024 aluminum alloy during the squeeze casting process
    Jahangiri, A.
    Marashi, S. P. H.
    Mohammadaliha, M.
    Ashofte, V.
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2017, 245 : 1 - 6
  • [30] Effect of Posttreatment on Microstructure and Magnetic Properties of Si Steel Strips Prepared by Twin-Roll Continuous Casting Process
    Yi, Yu
    Zhou, Zehua
    Wang, Zehua
    Jiang, Shaoqun
    Huang, Weidong
    [J]. METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE, 2012, 43 (05): : 1173 - 1176
12345