Numerical investigation of turbulence characteristics and upstream disturbance of flow through standard and multi-hole orifice flowmeters

被引:30
|
作者
Moosa, Morteza [1 ]
Hekmat, Mohamad Hamed [1 ]
机构
[1] Tafresh Univ, Dept Mech Engn, Tafresh 3951879611, Iran
关键词
Standard orifice; Multi-hole orifice; Discharge coefficient; Upstream disturbance; Pressure drop; Turbulence characteristics; PERFORATED PLATE; PERFORMANCE;
D O I
10.1016/j.flowmeasinst.2019.01.002
中图分类号
TH [机械、仪表工业];
学科分类号
0802 ;
摘要
In this research, the flow through the standard and improved multi-hole orifices of Shaaban, Singh and Huang is simulated numerically. The main objective is to study the turbulence characteristics of the downstream flow of the orifices, the discharge coefficient as the efficiency criterion of the orifices and the effect of disturbance of the upstream flow, due to putting an out of plane double elbow, on orifice performance and downstream flow characteristics. The three-dimensional steady, incompressible turbulent flow with a Reynolds number of 9200 is considered. The conservation equations are solved using finite volume method on hybrid meshes. The turbulence model employed in this research is the standard kappa-epsilon model. The simulation results indicate the gradual development of the turbulent kinetic energy and turbulent energy dissipation rate from the orifice plate to fully developed turbulent flow in the downstream of the standard orifice. However, for the multi-hole orifices, these characteristics are reduced at a higher rate with increasing the distance from orifice, and thus, unlike the standard orifice, it is possible to achieve a fully developed turbulent flow in a shorter downstream distance. In addition, all types of the improved orifices have the higher discharge coefficient with respect to the standard ones. Among them, Singh's model has the highest discharge coefficient. The numerical results indicate that for the ineffectiveness of the flow rate measurement from the upstream disturbance of the orifice, the straight pipe length between the source of disturbance and the orifice for the standard type should be at least 60 t greater than the pipe diameter. While this length is about 25 times greater than the diameter of the pipe for the multi-hole orifices. These three important advantages of the shorter length of the developing turbulent region, the higher discharge coefficient and the lower sensitivity to the upstream disturbances for the improved orifices compared to the standard type show an increase in the accuracy and efficiency of these new kinds of orifices while using them as the flowmeters.
引用
收藏
页码:203 / 218
页数:16
相关论文
共 50 条
  • [31] The influence of eccentric needle movement on internal flow and injection characteristics of a multi-hole diesel nozzle
    Wang, Chuqiao
    Moro, Adams
    Xue, Fuying
    Wu, Xiwen
    Luo, Fuqiang
    INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2018, 117 : 818 - 834
  • [32] Behavior and pressure drop of an upwardly two-phase flow through multi-hole orifices
    Zeghloul, Ammar
    Azzi, Abdelwahid
    Hasan, Abbas
    Azzopardi, Barry James
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE, 2018, 232 (18) : 3281 - 3299
  • [33] Ultrasensitive, Optofluidic Biomolecular Fluorescence Detection Using Flow-through, Multi-Hole Capillary
    Guo, Yunbo
    Oo, Maung Kyaw Khaing
    Hoyt, David
    Lamar, Dax
    Reddy, Karthik
    Fan, Xudong
    2012 CONFERENCE ON LASERS AND ELECTRO-OPTICS (CLEO), 2012,
  • [34] Towards higher accuracy and better frequency response with standard multi-hole probes in turbulence measurement with remotely piloted aircraft (RPA)
    Wildmann, N.
    Ravi, S.
    Bange, J.
    ATMOSPHERIC MEASUREMENT TECHNIQUES, 2014, 7 (04) : 1027 - 1041
  • [35] Experimental study of flow regime characteristics in diesel multi-hole nozzles with different structures and enlarged scales
    Zhong, Wenjun
    He, Zhixia
    Wang, Qian
    Shao, Zhuang
    Tao, Xicheng
    INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER, 2014, 59 : 1 - 10
  • [36] UNSTEADY NUMERICAL INVESTIGATION ON FILM COOLING CHARACTERISTICS OF THE TRAILING EDGE CUTBACK WITH UPSTREAM CYLINDER HOLE
    Xiao, Xiangtao
    Wang, Pei
    Xu, Qingzong
    Du, Qiang
    Liu, Jun
    Chang, Sheng
    PROCEEDINGS OF THE ASME TURBO EXPO: TURBOMACHINERY TECHNICAL CONFERENCE AND EXPOSITION, VOL 7B, PT II, 2020,
  • [37] Numerical investigation of the geometrical effects on UHMWPE flow characteristics in small aperture spinneret orifice
    Qin, Shengxue
    Zhang, Zhanhuan
    Xu, Xingming
    Liu, Jie
    Liu, Hong
    2015 GLOBAL CONFERENCE ON POLYMER AND COMPOSITE MATERIALS (PCM2015), 2015, 87
  • [38] Improvement of Multi-Hole Airflow Impingement on Flow and Heat Transfer Characteristics Inside a Turbine Vane Cavity
    Zhang, Lixi
    Cao, Gaopan
    Feng, Kai
    Jia, Yi
    Zhang, Zhengyang
    APPLIED SCIENCES-BASEL, 2021, 11 (21):
  • [39] Characteristics of the internal flow and the near-field spray of a single-hole injector and a multi-hole injector for diesel engines
    Dong, Pengbo
    Inaba, Takuya
    Nishida, Keiya
    Shimo, Daisuke
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART D-JOURNAL OF AUTOMOBILE ENGINEERING, 2016, 230 (05) : 632 - 649
  • [40] Spray characteristics of biofuel-gasoline blends through an asymmetric multi-hole injector of DISI engines
    Shi, Ling
    Fan, Qianwang
    PROCEEDINGS OF THE 5TH INTERNATIONAL CONFERENCE ON ADVANCED DESIGN AND MANUFACTURING ENGINEERING, 2015, 39 : 1642 - 1651