Numerical investigation of turbulence characteristics and upstream disturbance of flow through standard and multi-hole orifice flowmeters

被引:30
|
作者
Moosa, Morteza [1 ]
Hekmat, Mohamad Hamed [1 ]
机构
[1] Tafresh Univ, Dept Mech Engn, Tafresh 3951879611, Iran
关键词
Standard orifice; Multi-hole orifice; Discharge coefficient; Upstream disturbance; Pressure drop; Turbulence characteristics; PERFORATED PLATE; PERFORMANCE;
D O I
10.1016/j.flowmeasinst.2019.01.002
中图分类号
TH [机械、仪表工业];
学科分类号
0802 ;
摘要
In this research, the flow through the standard and improved multi-hole orifices of Shaaban, Singh and Huang is simulated numerically. The main objective is to study the turbulence characteristics of the downstream flow of the orifices, the discharge coefficient as the efficiency criterion of the orifices and the effect of disturbance of the upstream flow, due to putting an out of plane double elbow, on orifice performance and downstream flow characteristics. The three-dimensional steady, incompressible turbulent flow with a Reynolds number of 9200 is considered. The conservation equations are solved using finite volume method on hybrid meshes. The turbulence model employed in this research is the standard kappa-epsilon model. The simulation results indicate the gradual development of the turbulent kinetic energy and turbulent energy dissipation rate from the orifice plate to fully developed turbulent flow in the downstream of the standard orifice. However, for the multi-hole orifices, these characteristics are reduced at a higher rate with increasing the distance from orifice, and thus, unlike the standard orifice, it is possible to achieve a fully developed turbulent flow in a shorter downstream distance. In addition, all types of the improved orifices have the higher discharge coefficient with respect to the standard ones. Among them, Singh's model has the highest discharge coefficient. The numerical results indicate that for the ineffectiveness of the flow rate measurement from the upstream disturbance of the orifice, the straight pipe length between the source of disturbance and the orifice for the standard type should be at least 60 t greater than the pipe diameter. While this length is about 25 times greater than the diameter of the pipe for the multi-hole orifices. These three important advantages of the shorter length of the developing turbulent region, the higher discharge coefficient and the lower sensitivity to the upstream disturbances for the improved orifices compared to the standard type show an increase in the accuracy and efficiency of these new kinds of orifices while using them as the flowmeters.
引用
收藏
页码:203 / 218
页数:16
相关论文
共 50 条
  • [21] Numerical simulation and experimental validation of cavitating flow in a multi-hole diesel fuel injector
    Kumar, Aishvarya
    Ghobadian, Ali
    Nouri, Jamshid
    INTERNATIONAL JOURNAL OF ENGINE RESEARCH, 2022, 23 (06) : 958 - 973
  • [22] NUMERICAL INVESTIGATION ON THE EFFECT OF ADVANCED BREAKUP MODEL ON SPRAY SIMULATION OF A MULTI-HOLE INJECTOR
    Tripathy, Srinibas
    Sahoo, Sridhar
    Srivastava, Dhananjay Kumar
    PROCEEDINGS OF THE ASME INTERNAL COMBUSTION ENGINE FALL TECHNICAL CONFERENCE, 2018, VOL 2, 2019,
  • [23] Experimental and numerical investigation of geometric effect on cavitation flow through orifice
    Davoudi, Mohammad Reza
    Mahdi, Miralam
    MECHANICS & INDUSTRY, 2021, 22
  • [24] Experimental investigation on thermal stratification characteristic of steam condensation through multi-hole sparger
    Zhang, Dandi
    Wang, Shanpu
    Tong, Lili
    Cao, Xuewu
    APPLIED THERMAL ENGINEERING, 2023, 228
  • [25] Numerical Study of Single-Hole and Multi-Holes Orifice Flow Parameters
    Durdevic, M.
    Bukurov, M.
    Tasin, S.
    Bikic, S.
    JOURNAL OF APPLIED FLUID MECHANICS, 2021, 14 (01) : 215 - 226
  • [26] Numerical Investigation of the Influence of Bluff Body’s Shape on Flow Characteristics in Vortex Flowmeters
    V. E. Vershinin
    F. I. Polkovnikov
    Automation and Remote Control, 2019, 80 : 1368 - 1373
  • [27] Numerical Investigation of the Influence of Bluff Body's Shape on Flow Characteristics in Vortex Flowmeters
    Vershinin, V. E.
    Polkovnikov, F. I.
    AUTOMATION AND REMOTE CONTROL, 2019, 80 (07) : 1368 - 1373
  • [28] Investigation of deposit effect on multi-hole injector spray characteristics and air/fuel mixing process
    Wang, Bo
    Badawy, Tawfik
    Jiang, Yizhou
    Xu, Hongming
    Ghafourian, Akbar
    Zhang, Xinyu
    FUEL, 2017, 191 : 10 - 24
  • [29] Investigation on structural design and mechanical characteristics of the spherical multi-hole non-pneumatic tire
    Zang, Liguo
    Peng, Xinlei
    Li, Yaowei
    Lv, Tian
    Xue, Cheng
    Deng, Yaoji
    JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY, 2024, 38 (11) : 6141 - 6155
  • [30] A numerical investigation of effects of cavity and orifice parameters on the characteristics of a synthetic jet flow
    Jain, Manu
    Puranik, Bhalchandra
    Agrawal, Amit
    SENSORS AND ACTUATORS A-PHYSICAL, 2011, 165 (02) : 351 - 366