Optimization of curing cycle in carbon fiber-reinforced laminates: Void distribution and mechanical properties

被引：108
|
作者：
Hernandez, S. [1 ]
Sket, F. [1 ]
Gonzalez, C. [1 ,2 ]
LLorca, J. [1 ,2 ]
机构：
[1] IMDEA Mat Inst, Madrid 28906, Spain
[2] Univ Politecn Madrid, Dept Mat Sci, Madrid 28040, Spain
来源：
COMPOSITES SCIENCE AND TECHNOLOGY | 2013年 / 85卷
关键词：
Polymer-matrix composites; Curing; Mechanical properties; Porosity/voids; X-ray microtomography; INTERLAMINAR SHEAR-STRENGTH; CURE PRESSURE; COMPOSITES; BEHAVIOR; POLYMER; HEAT;
D O I：
10.1016/j.compscitech.2013.06.005
中图分类号：
TB33 [复合材料];
学科分类号：
摘要：
A strategy is presented to optimize out-of-autoclave processing of quasi-isotropic carbon fiber-reinforced laminates. Square panels of 4.6 mm nominal thickness with very low porosity (<= 0.2%) were manufactured by compression molding at low pressure (0.2 MPa) by careful design of the temperature cycle to maximize the processing window. The mechanisms of void migration during processing were ascertained by means of X-ray microtomography and the effect of ply clustering on porosity and on void shape was explained. Finally, the effect of porosity and ply clustering on the compressive strength before and after impact was studied. (C) 2013 Elsevier Ltd. All rights reserved.
引用
收藏
页码：73 / 82
页数：10
相关论文
共 50 条
  • [21] NONLINEAR MODEL OF THE MECHANICAL RESPONSE OF FIBER-REINFORCED LAMINATES TO MECHANICAL LOADING
    GRAHAM, U
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1991, 135 : 195 - 198
  • [22] Optimization of FDM parameters for enhanced mechanical properties of chopped carbon fiber-reinforced polymer composites
    Moghanlou, Mohammad Rouhi
    Azizian-Farsani, Elaheh
    Mahmoudi, Ali
    Khonsari, Michael M.
    PROGRESS IN ADDITIVE MANUFACTURING, 2025, 10 (04) : 2073 - 2088
  • [23] DETERMINATION OF EFFECTIVE PROPERTIES OF FIBER-REINFORCED COMPOSITE LAMINATES
    Skrzat, Andrzej
    Stachowicz, Feliks
    ADVANCES IN SCIENCE AND TECHNOLOGY-RESEARCH JOURNAL, 2014, 8 (22): : 56 - 59
  • [24] Effect of fiber length and composition on mechanical properties of carbon fiber-reinforced polybenzoxazine
    Kumar, K. S. Santhosh
    Nair, C. P. Reghunadhan
    Ninan, K. N.
    POLYMERS FOR ADVANCED TECHNOLOGIES, 2008, 19 (07) : 895 - 904
  • [25] Design optimization of fiber-reinforced laminates for maximum fatigue life
    Ertas, Ahmet H.
    Sonmez, Fazil O.
    JOURNAL OF COMPOSITE MATERIALS, 2014, 48 (20) : 2493 - 2503
  • [26] COMPRESSION STRENGTH OF ALIGNED CARBON FIBER-REINFORCED THERMOPLASTIC LAMINATES
    LEE, RJ
    COMPOSITES, 1987, 18 (01): : 35 - 39
  • [27] The Effect of Carbon Fiber Content on the Mechanical and Tribological Properties of Carbon Fiber-Reinforced PTFE Composites
    Li, J.
    POLYMER-PLASTICS TECHNOLOGY AND ENGINEERING, 2010, 49 (04) : 332 - 336
  • [28] Acoustic Imaging of microstructures of carbon fiber-reinforced composite laminates
    Liu, SP
    Levin, VM
    Guo, EM
    ADVANCED FIBERS, PLASTICS, LAMINATES AND COMPOSITES, 2002, 702 : 365 - 375
  • [29] Batch Optimization Algorithm for Autoclave Curing of Fiber-Reinforced Composites
    Philipp, T. R.
    Klein, T. P.
    Reinhart, G.
    2012 IEEE INTERNATIONAL CONFERENCE ON INDUSTRIAL ENGINEERING AND ENGINEERING MANAGEMENT (IEEM), 2012, : 438 - 443
  • [30] Crystallization behaviors and mechanical properties of carbon fiber-reinforced polypropylene composites
    Tian, Huafeng
    Zhang, Shuai
    Ge, Xiang
    Xiang, Aimin
    JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY, 2017, 128 (03) : 1495 - 1504
12345